<div dir="ltr">Sorry, don't have an electric code book. <div><br></div><div style>Someone out there must know an electrician?</div><div style><br></div><div style>-steve</div></div><div class="gmail_extra"><br><br><div class="gmail_quote">
On Sat, Jun 29, 2013 at 10:47 AM, Hol Gaskill <span dir="ltr"><<a href="mailto:hol@gaskill.com" target="_blank">hol@gaskill.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
all sounds good - we should avoid having ground loops where possible since it could throw off low voltage signals if there is strong EMI.  do you know offhand a good electrical code reference?  i have ugly's manual but haven't really done much with it...<br>

<div class="HOEnZb"><div class="h5"><br>
<br>
Jun 28, 2013 11:04:08 AM, <a href="mailto:steveberl@gmail.com">steveberl@gmail.com</a> wrote:<br>
Also need to consider grounding/lightning protection for anything on the rooftop. <br>
>Best bet would be to use any existing AC power that is already up there, and save this drop for low voltage, data, RF, etc. Ground everything to the AC power system ground that is hopefully already up there.<br>
<br>
>I assume the old (steam?) pipe is metal? It would be good to figure out if there is electrical continuity from end to end of the pipe. If it is, then grounding one end to the building power ground should be sufficient. If the conduit is not electrically continuous from end to end, it might be best to make sure both ends are grounded, or find out where the gap is and bridge across it with some kind of jumper.<br>

<br>
>-steve<br>
><br>
>On Fri, Jun 28, 2013 at 9:04 AM, Steve Berl <a href="mailto:steveberl@gmail.com">steveberl@gmail.com</a>> wrote:<br>
><br>
<br>
>Maybe a couple of RG/6 coax cables also?<br>
>It may not be cool to run 120VAC in the same conduit with the low voltage stuff. Check the electric code.<br>
<br>
><br>
-steve<br>
><br>
>On Fri, Jun 28, 2013 at 8:44 AM, Hol Gaskill <a href="mailto:hol@gaskill.com">hol@gaskill.com</a>> wrote:<br>
><br>
<br>
<br>
>Hi folks,<br>
><br>
<br>
><br>
Sounds like there's been some interest at various times in putting stuff on the roof.  I think we should install a waterproof junction box with a few power and data lines on the roof.  There is an old ventilation (steam?) port by the CNC router that I assume we could drop the cables through.  I'm thinking 120VAC up, 12 or 24VDC up/down for solar power, ethernet, and USB should suffice.  I bet there's already 120VAC up there but not sure if we are allowed to slurp directly.  Thoughts?  So far there have been discussions on mesh node, solar panels, uav control, air quality monitoring to name a few.<br>

><br>
<br>
<br>
<br>
><br>
cheers,<br>
><br>
hol<br>
><br>
_______________________________________________<br>
><br>
sudo-discuss mailing list<br>
><br>
<a href="mailto:sudo-discuss@lists.sudoroom.org">sudo-discuss@lists.sudoroom.org</a><br>
><br>
<a href="http://lists.sudoroom.org/listinfo/sudo-discuss" target="_blank">http://lists.sudoroom.org/listinfo/sudo-discuss</a><br>
><br>
<br>
><br>
><br>
>--<br>
>-steve<br>
<br>
<br>
><br>
><br>
>--<br>
>-steve<br>
<br>
</div></div></blockquote></div><br><br clear="all"><div><br></div>-- <br>-steve
</div>