<div dir="ltr"><div>i think we're gunna have to mount a larger fan to the underside of teh skylight thing that's bolted to teh rafter.<br></div><div>we can reach it w/scaffolding<br>might be a good time to install some diffusion under teh skylights 2<br></div><div><br></div></div><div class="gmail_extra"><br><div class="gmail_quote">On Fri, Sep 23, 2016 at 11:53 AM, Jake <span dir="ltr"><<a href="mailto:jake@spaz.org" target="_blank">jake@spaz.org</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">we have a duct fan, it's under the laser cutter to the left of its cart last i saw it, it's a beige and blue metal box the size of a small TV/VCR combo, and it has two 4" duct things on the back. It would need some modification to work with the exhaust duct we have (cardboard and duct tape or something from the hardware store or a cut-up plastic bucket)<br>
<br>
and then its inlet can be ducted to our acrylic fume hood box thing, or to whatever we're trying to ventilate.<br>
<br>
also don't forget someone should go on the roof and reposition the top of the duct in the skylight thing so it's centered over its hole, so it doesn't leak back into the room like it does now.<div class="HOEnZb"><div class="h5"><br>
<br>
On Thu, 22 Sep 2016, robb wrote:<br>
<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
we need a duct fan<br>
<br>
<br>
On Thu, Sep 22, 2016 at 8:50 PM, Jake <<a href="mailto:jake@spaz.org" target="_blank">jake@spaz.org</a>> wrote:<br>
<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
that's hilarious, i guess it would be perfect for what Trent wants to do.<br>
<br>
make sure you get plenty of ventilation, i should have mentioned.<br>
<br>
This can't be done in sudoroom without running a fan to the ventilation<br>
duct near the laser cutter. Perhaps the clear acrylic flow-hood could be<br>
connected to a ventilation blower to the exhaust duct.<br>
<br>
-jake<br>
<br>
<br>
On Thu, 22 Sep 2016, robb wrote:<br>
<br>
i just found a 10.5" X 20" electric hotplate yesterday.<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
it's on the projects shelves past the robot arm w/a note about component<br>
removal use on it.<br>
<br>
On Thu, Sep 22, 2016 at 3:39 PM, Trent Robbins <<a href="mailto:robbintt@gmail.com" target="_blank">robbintt@gmail.com</a>><br>
wrote:<br>
<br>
Thanks Jake! I was planning on doing it by hand, but it would be neat to<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
try the mechanical one at sudo room.<br>
<br>
Trent<br>
<br>
On Thursday, September 22, 2016, Jake <<a href="mailto:jake@spaz.org" target="_blank">jake@spaz.org</a>> wrote:<br>
<br>
a hotplate covered with clean sand heated up to 400 degrees (celsius)<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
will be a surface on which you can place a circuitboard covered with<br>
such<br>
switches, and then you can pluck them out of the board as their solder<br>
melts. This is how old boards had their parts salvaged from them back<br>
when<br>
people still did that.<br>
<br>
if you don't have the right hotplate and you want to use a skillet<br>
instead, you'll likely have to cut the circuitboard in half or thirds so<br>
that it will be small enough to fit in the skillet of sand. no big<br>
deal.<br>
<br>
you could also remove them one at a time, using a desoldering tool.<br>
There's a motorized one at sudoroom, which is basically a gun-shaped<br>
soldering iron with a hollow tip and a foot-pedal activated vacuum pump.<br>
You could use that to pull the solder out of the hole for one of the two<br>
pins of each key, and then use a regular soldering iron to heat up the<br>
second one while pulling the key out with the other hand.<br>
<br>
good luck,<br>
-jake<br>
<br>
On Tue, 20 Sep 2016, Trent Robbins wrote:<br>
<br>
Does anyone know a good way to salvage from 101-105 mx brown keyboard<br>
<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
switches?<br>
<br>
I'm planning on building my own keyboard this fall or winter and have<br>
plenty of time to source scrap.<br>
<br>
<a href="http://cubiq.org/build-your-very-own-pc-keyboard" rel="noreferrer" target="_blank">http://cubiq.org/build-your-ve<wbr>ry-own-pc-keyboard</a><br>
<br>
Build process is as complex as you'd expect.<br>
<br>
Teensy firmware: <a href="https://github.com/tmk/tmk_keyboard" rel="noreferrer" target="_blank">https://github.com/tmk/tmk_key<wbr>board</a><br>
<br>
<br>
<br>
Trent<br>
<br>
<br>
<br>
</blockquote></blockquote>
--<br>
(Sent from cellphone)<br>
<br>
______________________________<wbr>_________________<br>
sudo-discuss mailing list<br>
<a href="mailto:sudo-discuss@lists.sudoroom.org" target="_blank">sudo-discuss@lists.sudoroom.or<wbr>g</a><br>
<a href="https://sudoroom.org/lists/listinfo/sudo-discuss" rel="noreferrer" target="_blank">https://sudoroom.org/lists/lis<wbr>tinfo/sudo-discuss</a><br>
<br>
<br>
<br>
</blockquote>
<br>
</blockquote></blockquote>
<br>
</blockquote>
</div></div></blockquote></div><br></div>