<div dir="ltr"><div><div>Sorry for trying to be helpful, but I don't think you could expect me to magically know those details. It just seemed better to use the Lulzbot resistor that you listed in your first email.<br><br></div>Patrik<br><br></div>PS: the resistor recommended by Lulzbot is <a href="https://www.digikey.com/product-detail/en/vishay-sfernice/RWM06224R70JA15E1/RWMB-4.7CT-ND/1587939?utm_adgroup=Resistors&gclid=CjwKCAiAhfzSBRBTEiwAN-ysWEwePIQ6Rl2PioHblQy56f0W38XUWEMqlF8XKOAmPfNA1bfxALw10BoCBPwQAvD_BwE">available on Digi-Key for $1.50</a> - might not help if it's the wrong resistance tho.<br></div><div class="gmail_extra"><br><div class="gmail_quote">On Wed, Jan 17, 2018 at 3:48 PM, Jake <span dir="ltr"><<a href="mailto:jake@spaz.org" target="_blank">jake@spaz.org</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Patrik if we don't glue it in, it won't make thermal contact with the aluminum<br>
block and will burn out.  Thermal paste gets squeezed out when the resistor<br>
heats up and expands and then you end up with a gap and the resistor burns out.<br>
<br>
We already went down the road with the Lulzbot resistor that is out of stock,<br>
permanently.  It's also the wrong resistance, and the software patch to<br>
compensate for that fact doesn't work.  I carefully chose this resistor value<br>
(8 ohms) and the thermally conductive epoxy that I want to use to glue it in.<br>
<br>
if you want to take over this project go ahead, but sowing doubt and<br>
uncertainty will just leave us with no 3D printer for another three years.<span class="HOEnZb"><font color="#888888"><br>
<br>
-jake</font></span><div class="HOEnZb"><div class="h5"><br>
<br>
On Wed, 17 Jan 2018, Patrik D'haeseleer wrote:<br>
<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
On Wed, Jan 17, 2018 at 4:04 AM, Jake <<a href="mailto:jake@spaz.org" target="_blank">jake@spaz.org</a>> wrote:<br>
<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<br>
If someone gets the resistor shaved to fit in there, i'll bring in the<br>
special two-part thermal bonding epoxy and glue it in, and then i'll hook up<br>
the wires and we'll have a 3D printer again.<br>
</blockquote>
<br>
Don't glue it in place with epoxy, or you'll have to drill it out when it<br>
burns out again. It should be a tight enough fit to hold in place by itself,<br>
no? I would expect regular thermal paste to conducts heat better than the<br>
epoxy anyway...<br>
<br>
Patrik<br>
<br>
PS: the replacement resistor that Lulzbot sells is only $3.50, and I would<br>
expect that one to fit the hole like a glove. They seem to be out of stock<br>
right now though...<br>
</blockquote>
</div></div></blockquote></div><br></div>