<div dir="ltr"><div>shoot, I was hoping to have the board 100% tested and working before paste/pick'n'place more, but I've been pretty swamped the last two weeks.</div><div><br></div><div>I finished up the firmware today, and tested most of features. I'm pretty confident the board is good to go, but theres a small chance some components values could still change</div></div><br><div class="gmail_quote"><div dir="ltr">On Tue, Dec 18, 2018 at 6:56 PM robb <<a href="mailto:sf99er@gmail.com" target="_blank">sf99er@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="ltr">holidayz...<br></div><br><div class="gmail_quote"><div dir="ltr">On Tue, Dec 18, 2018 at 6:47 PM Jake <<a href="mailto:jake@spaz.org" target="_blank">jake@spaz.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">seriously no one had anything to say about any of this?<br>
<br>
On Wed, 5 Dec 2018, Jake wrote:<br>
<br>
> last night at sudoroom i did some things to get solder paste flowing from the<br>
> TAZ 3 3d printer.<br>
><br>
> i brought in a compact air compressor and adjusted its power switch to click<br>
> off around 100 PSI (since it was failing to reach its design pressure in a<br>
> reasonable amount of time and we only need like 40-50PSI for solder paste)<br>
><br>
> i'm not sure if it's still working because it cut out apparently due to heat<br>
> the last time i was running it, but possibly just because of duty cycle.  It<br>
> needs a fitting installed into the outlet to plumb it to the solenoid.<br>
> Fittings are in the box behind the printer and there's teflon tape in the<br>
> "tape" box on the shelves in sudoroom.<br>
><br>
> i installed a three-port solenoid on the 3d printer which plugs in instead of<br>
> the extruder resistor / temperature sensor.  It contains a 47KΩ resistor to<br>
> simulate a thermistor (to avoid a fault code) and it wires the nozzle heater<br>
> wires to the three-port solenoid (which is rated at 24VDC matching the<br>
> printer's power supply)<br>
><br>
> I piped the 3-port solenoid to a syringe and mounted a syringe holder on the<br>
> print head assembly in a reasonable place.  A syringe of solder paste is in <br>
> the<br>
> sudoroom fridge and can be used.  Needles of various sizes are in the <br>
> cardboard<br>
> box behind the 3d printer.<br>
><br>
> the air compressor's outlet needs to be plumbed to the flexible black hose<br>
> going to the 3-port solenoid.  The solenoid needs to be mounted to the print<br>
> head (a twist-tie should work).<br>
><br>
> unfortunately the 3D printer's firmware seems to be cycling power to the <br>
> nozzle<br>
> resistor when a temperature is selected, probably because of PID parameters, <br>
> so<br>
> we will have to look for a set of commands (or modified firmware) to activate<br>
> the solenoid properly during the dispensing process.  This printer doesn't <br>
> seem<br>
> to have wires for a print head fan, which is how we connected the solenoid in<br>
> past implementations of this setup.  There will need to be a script or<br>
> modification to rpt2pnp to issue the right commands for this setup.<br>
><br>
> as a reminder the software for creating g-code to dispense solder paste from<br>
> the .rpt file output of a KiCAD circuitboard project is here:<br>
><br>
> <a href="https://github.com/hzeller/rpt2paste" rel="noreferrer" target="_blank">https://github.com/hzeller/<wbr>rpt2paste</a><br>
><br>
> note that it's superseded by<br>
><br>
> <a href="https://github.com/hzeller/rpt2pnp" rel="noreferrer" target="_blank">https://github.com/hzeller/<wbr>rpt2pnp</a><br>
><br>
> which may be newer.  the latter was confirmed to (apparently) correctly <br>
> process<br>
> the .rpt file from the project we'll likely dispense solder paste onto first:<br>
><br>
> <a href="https://github.com/fitzdoingprojects/big_battery" rel="noreferrer" target="_blank">https://github.com/<wbr>fitzdoingprojects/big_battery</a><br>
><br>
> i'll be gone for two weeks but if anyone wants to make progress on this <br>
> project<br>
> please write back and i'll help as much as i can.<br>
><br>
> -jake_________________________<wbr>______________________<br>
sudo-discuss mailing list<br>
<a href="mailto:sudo-discuss@lists.sudoroom.org" target="_blank">sudo-discuss@lists.sudoroom.<wbr>org</a><br>
<a href="https://sudoroom.org/lists/listinfo/sudo-discuss" rel="noreferrer" target="_blank">https://sudoroom.org/lists/<wbr>listinfo/sudo-discuss</a><br>
</blockquote></div>
</blockquote></div>