<div dir="ltr">Hi Yar, <div><br>Sorry that you got frustrated with the Switches and WAPs situation. <br><br>It's been years since the setup of the HP Switches, and the Wireless Access Points happened, so I don't recall all the details right now. <br><br>But, I do remember that I left a server room log notebook on top of the server, next to the monitor, describing the work done. <br><br>Also, I left a paper sheet taped against the wall detailing the switch ports that were in use, and where they were coming from.  <br><br>At that time I remember you had two VLANs, a Private, and a Public one. <br>I put one HP switch, along with the Ruckus Wireless Controller on the publick VLAN. <div><br>I also recall sending you a Signal message with the switches log credentials, and additional informacion. I do not have that info anymore, because I have switched to a newer phone since then. <br><br>However, resetting the admin password allows access to the admin console of the HP switch(s). Clearing the HP Switch Admin Password:<br>When the switch is running with a paper clip push in the small hole that is labeled "<b>CLEAR</b>", for about 5-10 seconds. It will clear the password, and should allow admin access. Do NOT push the reset button, it will erase the whole configuration. <br><br>I remember labeling every single switch port for each switch and WAP. The info includes/included Switches, and WAPSs location, Switches/WAPs IP addresses, etc.  <br><br>I know it would be nicer/best to have put that informacion on the Wiki, that's on me. But, at the time I chose to do that server log notebook just to be more on the sec side of things. Info just for us, and not for the public in general.<br><br>Hope that helps.<br><br>Daniel<br><br><br><br></div></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Tue, Sep 8, 2020 at 9:13 PM Yardena Cohen <<a href="mailto:yardenack@gmail.com">yardenack@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">I've been troubleshooting at omni for a while now. The wifi appears to<br>
work for me, as do the main gateway and the door computer, but various<br>
ethernet-connected devices do not work. I don't know why, but I<br>
suspect the problem is one of the switches is either misconfigured or<br>
malfunctioning, or the maze of ethernet got incorrectly rearranged<br>
somehow in yesterday's withdrawal-induced panic.<br>
<br>
I didn't set up these switches, or the connections throughout the<br>
building, the cables are not labelled, and I don't know if the<br>
switches are documented. I'm exhausted and frustrated because I<br>
couldn't figure this out in 2 hours, because things weren't labelled,<br>
and because there's so many people in the building who don't seem to<br>
be here for essential work, and/or who aren't wearing masks or wearing<br>
them improperly.<br>
<br>
I'm not even enthusiastic about making the public computers or office<br>
computers work again, because I'm not convinced they are essential<br>
enough to encourage people to sit around and put food service workers<br>
at greater risk.<br>
<br>
So I'm going home. Sorry all, someone else will have to figure this out.<br>
_______________________________________________<br>
sudo-sys mailing list<br>
<a href="mailto:sudo-sys@lists.sudoroom.org" target="_blank">sudo-sys@lists.sudoroom.org</a><br>
<a href="https://sudoroom.org/lists/listinfo/sudo-sys" rel="noreferrer" target="_blank">https://sudoroom.org/lists/listinfo/sudo-sys</a><br>
</blockquote></div>