if you put a 1 ohm resistance, you will just blow up the resistor.
24 volts divided by 1 ohm = 24 amps
24 volts times 24 amps = 576 watts
you need to find the highest number of ohms that will still cause the motor controller to not give you an error. Lets say you find that a 100 ohm resistor (in place of the missing motor) causes the controller to be OK. When you move the joystick, and it tries to turn the fake motor, it will give it up to 24volts. But it's a 100 ohm resistor.
24v / 100 ohm = 0.24 amps
24v * 0.25 amps = 5.76 watts
if it works with a 100 ohm, you should use that. 5.76 watts is reasonable. 576 watts is most of a horsepower and is not reasonable.
5
in case you're not confused i'll tell you this: the power a motor consumes (from a fixed voltage source for example) depends on the amount of force it's putting out.
So if you have a motor just spinning a wheel in the air it doesn't take as much power as if you're making it grind grain, or push a fat person up a steep incline. The ohms you measure when you use a multimeter on the stopped motor correspond to its MAXIMUM power, basically.
so if you stopped the motor and applied 24v, 576 watts would flow through it and heat it up pretty fast. But if you let it spin freely in the air, its effective impedance would be much higher than 1 ohm!
as for how to isolate the motors for different jobs.. we can read the manual on the control box and adjust the settings, or just hook up the computer control and let it do all the work. I don't know though.
-jake
On Thu, 16 Jul 2015, Robert Benson wrote:
i'm such an idiot. when i checked the motor resistance, i checked the controller's motor circuit resistance. the actual motor resistance is 1 ohm.
however, even idiots get lucky...the motor worked with 100ohm. having realized the above, i will not power it again until i find a 1ohm resistor.
for the record, moving the joystick in any direction moves the wheel in some way. so how do we isolate the motors for different jobs?
On Thu, Jul 16, 2015 at 12:49 AM, Jake <jake@spaz.org> wrote:
what do you mean both motors
you only have one motor last i checked.
On Thu, 16 Jul 2015, Robert Benson wrote:
my ohmmeter had a "k" in front of the ohm symbol when it read 150 k ; not a M or just the ohm symbol.
datasheet i posted earlier seemed to suggest the motor is 120V while the brake solenoid is 24V
both motors read 150kiloohm :/
On Wed, Jul 15, 2015 at 11:45 PM, Robert Benson <sf99er@gmail.com> wrote:
gonna have to have a high wattage rating, huh?
On Wed, Jul 15, 2015 at 11:41 PM, Robert Benson <sf99er@gmail.com> wrote:
150k says the motor
on hunt for same
On Wed, Jul 15, 2015 at 11:30 PM, Jake <jake@spaz.org> wrote:
a wire jumper is approximately zero ohms, which will destroy stuff when power flows through it.
the motor controller is complaining because it sees infinity ohms across the missing motor's terminals. So just like the brake, the
solution is to put a resistor across the missing motor's terminals.
if we want more than one motor, we can just put the other motor on the missing connector and use the one controller to control both
motors.
if we need more than two motors, we can use relays or switches with the same controller, or we could get more controllers. But lets
start
with one or two motors.
-jake
On Wed, 15 Jul 2015, Robert Benson wrote:
agreed
i was thinking that since controller still said check right motor connector after i crossed the brake terminals w/resistor that
i needed to jump it. when i jumped
them the check right motor code went out which seemed to indicate the error was corrected. luckily i had to hold the jump wire &
resistors against the contacts so i
noticed the heat immediately after touching the joystick and cut the power. check right brake code has returned as before.
maybe building a 120vac/24vdc controller would be better...we probably want four or more of these puppies for the lighting
trusses
On Wed, Jul 15, 2015 at 11:00 PM, Jake <jake@spaz.org> wrote:
you should not short out stuff with even a thin wire.
you are going to destroy the motor controller if you continue on this path
what are you thinking? do not short out the motor terminals.
On Wed, 15 Jul 2015, Robert Benson wrote:
connected a thin wire across motor side of connector (while 110ohm across brake side) and got movement but wire got
real hot...too scared
i'll damage the controller
right now to try a bigger gauge
On Wed, Jul 15, 2015 at 10:26 PM, Robert Benson <sf99er@gmail.com> wrote:
connected 110ohm across brake terminals but no worky
On Wed, Jul 15, 2015 at 9:44 PM, Jake <jake@spaz.org> wrote:
should be fine
On Wed, 15 Jul 2015, Robert Benson wrote:
might have to upgrade the roomba motor & controller to hit mice
will 150ohms be too much/work/hurt anything? i found a 100ohm 5w & 50ohm ?w i plan on running in series
if i dont find a more suitable value
On Wed, Jul 15, 2015 at 8:21 PM, Patrik D'haeseleer <patrikd@gmail.com> wrote:
On Jul 15, 2015 6:05 PM, "Jake" <jake@spaz.org> wrote:
if you want to play with robots i have plenty, like roombas which won't break
your legs running you over.
Roomba + tazer = no more mouse problems!
Patrik