Beagle Bone Black - Revision history

Ubiquitous: /* Configuring B.A.T.M.A.N to Mesh with Sudo Mesh */

2014-06-18T04:22:20Z

Configuring B.A.T.M.A.N to Mesh with Sudo Mesh

← Older revision		Revision as of 21:22, 17 June 2014
Line 37:		Line 37:
	'''Mesh the planet...'''		'''Mesh the planet...'''
	=Configuring B.A.T.M.A.N to Mesh with Sudo Mesh=		=Configuring B.A.T.M.A.N to Mesh with Sudo Mesh=
	This tutorial assumes that you have your Beagle Bone configured running Debian Wheezy.		This tutorial assumes that you have your Beagle Bone configured running Debian Wheezy. It is all recommended that you disabel network-manager.


			Add batman module to the kernel
	<pre>		<pre>

	modprobe batman-adv		modprobe batman-adv
			</pre>
			Add B.A.T.M.A.N interface
			<pre>
	batctl if add eth0		batctl if add eth0
			</pre>
			Disable Wifi
			<pre>
	ifconfig wlan0 down		ifconfig wlan0 down
			</pre>
			Set MTU
			<pre>
	ifconfig wlan0 mtu 1532		ifconfig wlan0 mtu 1532
	iwconfig wlan0 mode ad-hoc essid pplsopen.net-node2node \		</pre>
	ap CA:FE:C0:DE:F0:0D channel 11		Turn on Ad-Hoc Mode and connect to the SSID ppslopen.net-node2node with the Mac Address CA:FE:C0:DE:F0:0D on Channel 11
			<pre>
			iwconfig wlan0 mode ad-hoc essid pplsopen.net-node2node ap CA:FE:C0:DE:F0:0D channel 11
			</pre>
			Connect B.A.T.M.A.N interface to Wlan
			<pre>
	batctl if add wlan0		batctl if add wlan0
			</pre>
			Turn on wlan0 and bat0 interfaces
			<pre>
	ifconfig wlan0 up		ifconfig wlan0 up
	ifconfig bat0 up		ifconfig bat0 up
			</pre>
			Connect to your network. Subject to change depending on our network's subnet
			<pre>
	ifconfig bat0 10.200.8.1		ifconfig bat0 10.200.8.1
	route add default gw 10.0.99.1		route add default gw 10.0.99.1
			</pre>
			Enable Port Forwarding
			<pre>
	echo 1 > /proc/sys/net/ipv4/ip_forward		echo 1 > /proc/sys/net/ipv4/ip_forward

	</pre>		</pre>

Ubiquitous at 04:07, 18 June 2014

2014-06-18T04:07:06Z

← Older revision		Revision as of 21:07, 17 June 2014
Line 36:		Line 36:
	<br><br><br>		<br><br><br>
	'''Mesh the planet...'''		'''Mesh the planet...'''
			=Configuring B.A.T.M.A.N to Mesh with Sudo Mesh=
			This tutorial assumes that you have your Beagle Bone configured running Debian Wheezy.

			<pre>

			modprobe batman-adv
			batctl if add eth0
			ifconfig wlan0 down
			ifconfig wlan0 mtu 1532
			iwconfig wlan0 mode ad-hoc essid pplsopen.net-node2node \
			ap CA:FE:C0:DE:F0:0D channel 11
			batctl if add wlan0
			ifconfig wlan0 up
			ifconfig bat0 up
			ifconfig bat0 10.200.8.1
			route add default gw 10.0.99.1
			echo 1 > /proc/sys/net/ipv4/ip_forward

			</pre>

Chrisjx at 04:44, 11 April 2014

2014-04-11T04:44:22Z

← Older revision		Revision as of 21:44, 10 April 2014
Line 2:		Line 2:

	notes about BBB - Beagle Bone Black		notes about BBB - Beagle Bone Black

			== OS Install ==

			=== OpenWRT ===
			* https://github.com/artekw/openwrt-bbb

			=== Adafruit tutorial ===
			https://learn.adafruit.com/beaglebone-black-installing-operating-systems/angstrom


	== first light ==		== first light ==
			Just booting up...

	=== using an FTDI device plugged into J1 pins ===		=== using an FTDI device plugged into J1 pins ===

Chrisjx at 04:35, 11 April 2014

2014-04-11T04:35:28Z

← Older revision		Revision as of 21:35, 10 April 2014
Line 7:		Line 7:
	=== using an FTDI device plugged into J1 pins ===		=== using an FTDI device plugged into J1 pins ===

	find the serial port for the FTDI adapter		find the serial port for the FTDI USB adapter
	ls /dev/tty*		ls /dev/tty*

Chrisjx at 04:34, 11 April 2014

2014-04-11T04:34:21Z

← Older revision		Revision as of 21:34, 10 April 2014
Line 1:		Line 1:
	See Also:		See Also: [[Mesh/Hardware_support#Fourth_milestone \| Mesh/Hardware Fourth Milestone]]

	notes about BBB - Beagle Bone Black		notes about BBB - Beagle Bone Black

Chrisjx: Created page with "See Also: notes about BBB - Beagle Bone Black == first light == === using an FTDI device plugged into J1 pins === find the serial port for the FTDI adapter ls /dev/tty*..."

2014-04-11T04:32:32Z

Created page with "See Also: notes about BBB - Beagle Bone Black == first light == === using an FTDI device plugged into J1 pins === find the serial port for the FTDI adapter ls /dev/tty*..."

New page

See Also:

notes about BBB - Beagle Bone Black

== first light ==

=== using an FTDI device plugged into J1 pins ===

find the serial port for the FTDI adapter
ls /dev/tty*

* might be /dev/ttyAMA0 on linux
* might be /dev/tty.usbmodemfa133 on mac

Wiring from the FTDI device:
* BBB - FTDI
* pin 1 GND - GND
* pin 4 RX - TX
* pin 5 TX - RX

in terminal:
screen <usbdevicename> 115200

* first login with root, no password

<br><br><br>
'''Mesh the planet...'''