Custom 3D Printer - Revision history

Jerkey at 08:59, 4 December 2025

2025-12-04T08:59:48Z

← Older revision		Revision as of 01:59, 4 December 2025
Line 3:		Line 3:
	* [https://sudoroom.org/lists/hyperkitty/list/sudo-discuss@sudoroom.org/thread/Y2T3YOU5OBPD3U6DMMOKJ3CFRCLO6SLR/ email thread]		* [https://sudoroom.org/lists/hyperkitty/list/sudo-discuss@sudoroom.org/thread/Y2T3YOU5OBPD3U6DMMOKJ3CFRCLO6SLR/ email thread]

			* Recently R came through and helped work on this with Avery, apparently it's a "VORON" 3d printer. Here are their notes:<code>
			Octopus pro 1.0
			klipper via mainsail
			connect via ip
			127.0.0.1

			Printer CFG is currrently a hack and slash from another voron config
			!LOOK AT THE SENSOR SECTION, CHECK THE BED SENSOR AND PINS. SERIOUSLY. IT IS IMPORTANT.!</code>

	---------- Forwarded message ----------		---------- Forwarded message ----------

Romyilano at 03:05, 18 October 2023

2023-10-18T03:05:33Z

← Older revision		Revision as of 20:05, 17 October 2023
Line 2:		Line 2:

	* [https://sudoroom.org/lists/hyperkitty/list/sudo-discuss@sudoroom.org/thread/Y2T3YOU5OBPD3U6DMMOKJ3CFRCLO6SLR/ email thread]		* [https://sudoroom.org/lists/hyperkitty/list/sudo-discuss@sudoroom.org/thread/Y2T3YOU5OBPD3U6DMMOKJ3CFRCLO6SLR/ email thread]



			---------- Forwarded message ----------
			Date: Tue, 25 Jul 2023 21:39:31 -0700
			From: Scott Griffitts
			Subject: Re: [sudo-info] 3D printer donation

			Hey, Dropped off the printer with Toby and met a few folks who were excited,
			skeptical, and questioning the printer. I figured I would share some info on
			it.

			Here is the page on the upgraded Z mod I did: https://seckit3dp.design/kit/triple-z

			Here is the page for the main printer build: https://github.com/SecKit/SK-Go_SK-Mini

			Here is some info on the firmware it can run: https://www.klipper3d.org/
			(I think if you do some digging, you can find examples for the kinematic bed)

			Here is the bed probe I
			used: https://coex3d.com/products/bltouch-v3-1-automatic-bed-leveling-probe

			The stepper motor board used is big tree tech octopus v1.0 with TMC2209 drivers

			If you have any other questions let me know :)

			Also,
			If you guys need volunteers or anything, let me know. I’d love to help out with really
			cool people like you guys.

			Regards
			Scott Griffitts

Romyilano: Created page with "This seems to be a custom 3D printer that was donated in the summer of 2023 * [https://sudoroom.org/lists/hyperkitty/list/sudo-discuss@sudoroom.org/thread/Y2T3YOU5OBPD3U6DMMOKJ3CFRCLO6SLR/ email thread]"

2023-10-18T03:04:46Z

Created page with "This seems to be a custom 3D printer that was donated in the summer of 2023 * [https://sudoroom.org/lists/hyperkitty/list/sudo-discuss@sudoroom.org/thread/Y2T3YOU5OBPD3U6DMMOKJ3CFRCLO6SLR/ email thread]"

New page

This seems to be a custom 3D printer that was donated in the summer of 2023

* [https://sudoroom.org/lists/hyperkitty/list/sudo-discuss@sudoroom.org/thread/Y2T3YOU5OBPD3U6DMMOKJ3CFRCLO6SLR/ email thread]