Mesh/Firmware/Flash - Revision history

Matt: /* NanoStation */ adds instructions

2014-09-01T09:12:15Z

NanoStation: adds instructions

← Older revision		Revision as of 02:12, 1 September 2014
Line 43:		Line 43:

	===NanoStation===		===NanoStation===
			====NanoStation Loco M2====
			See information on the [http://wiki.openwrt.org/toh/ubiquiti/nanostationm2?s%5B%5D=nanostation&s%5B%5D=loco&s%5B%5D=m2 openwrt wiki]. Use same installation procedure as [[Mesh/Firmware/Flash#PicoStation]] above, but instead, use this image:

			openwrt-ar71xx-generic-ubnt-nano-m-squashfs-factory.bin

	===NanoBridge===		===NanoBridge===

Matt: /* PicoStation */ typo

2014-05-20T05:38:21Z

PicoStation: typo

← Older revision		Revision as of 22:38, 19 May 2014
Line 18:		Line 18:
	#* There is a small hole in the body of the router next to the ethernet port. Prepare to use a paperclip or similar small, sturdy poking device to push a 'reset button' that sits just inside this small hole.		#* There is a small hole in the body of the router next to the ethernet port. Prepare to use a paperclip or similar small, sturdy poking device to push a 'reset button' that sits just inside this small hole.
	#* Prepare to plug the router back in to the POE injector. You may need a friend to help.		#* Prepare to plug the router back in to the POE injector. You may need a friend to help.
	#* With your poking device, ~~old~~ the reset button down and plug the router back in to the POE injector. Hold the reset button until the router's green light goes to two, then starts flashing orange and red. Release the reset button when the lights flash for the second time.		#* With your poking device, hold the reset button down and plug the router back in to the POE injector. Hold the reset button until the router's green light goes to two, then starts flashing orange and red. Release the reset button when the lights flash for the second time.
	# Copy firmware to router using TFTP		# Copy firmware to router using TFTP
	#* After resetting the router, it should now be running a TFTP server at 192.168.1.20		#* After resetting the router, it should now be running a TFTP server at 192.168.1.20

Matt: updates install script name

2014-05-14T08:15:12Z

updates install script name

← Older revision		Revision as of 01:15, 14 May 2014
Line 1:		Line 1:
	Instructions on flashing routers (installing) with the sudo mesh firmware, [https://github.com/sudomesh/sudowrt-firmware sudowrt]! Based on the initial [[Mesh/WalkThrough]] document, but simplified and specific to supported hardware models.		Instructions on flashing routers (installing) with the sudo mesh firmware, [https://github.com/sudomesh/sudowrt-firmware sudowrt]! Based on the initial [[Mesh/WalkThrough]] document, but simplified and specific to supported hardware models.

	Check progress on this script for flashing nodes quickly: [https://github.com/sudomesh/sudowrt-flash ~~install.sh~~]		Check progress on this script for flashing nodes quickly: [https://github.com/sudomesh/sudowrt-flash sudowrt-flash]

	=Supported Devices=		=Supported Devices=

Matt: updated

2014-05-14T08:14:51Z

updated

← Older revision		Revision as of 01:14, 14 May 2014
Line 1:		Line 1:
	Instructions on flashing routers (installing) with the sudo mesh firmware, [https://github.com/sudomesh/sudowrt-firmware sudowrt]! Based on the initial [[Mesh/WalkThrough]] document, but simplified and specific to supported hardware models.		Instructions on flashing routers (installing) with the sudo mesh firmware, [https://github.com/sudomesh/sudowrt-firmware sudowrt]! Based on the initial [[Mesh/WalkThrough]] document, but simplified and specific to supported hardware models.

	~~There will soon be a~~ script for flashing ~~based on this old~~ [https://github.com/sudomesh/~~openwrt~~-~~to-sudowrt/blob/master/flash_router.sh~~ install.sh ~~(deprecated)~~]		Check progress on this script for flashing nodes quickly: [https://github.com/sudomesh/sudowrt-flash install.sh]

	=Supported Devices=		=Supported Devices=

Matt: /* Supported Devices */ removes bullet, unsupported hardware

2014-05-14T05:49:41Z

Supported Devices: removes bullet, unsupported hardware

← Older revision		Revision as of 22:49, 13 May 2014
Line 41:		Line 41:
	# Configure		# Configure
	#* Now your node is ready to be configured. Bring it to [[Sudoroom\|sudo room]] to configure your node using the build server!		#* Now your node is ready to be configured. Bring it to [[Sudoroom\|sudo room]] to configure your node using the build server!

	~~===Bullet===~~

	===NanoStation===		===NanoStation===

	===NanoBridge===		===NanoBridge===

Matt: updates description

2014-05-14T05:49:11Z

updates description

← Older revision		Revision as of 22:49, 13 May 2014
Line 1:		Line 1:
	Instructions on flashing routers with the sudo mesh firmware, [https://github.com/sudomesh/sudowrt-firmware sudowrt]!		Instructions on flashing routers (installing) with the sudo mesh firmware, [https://github.com/sudomesh/sudowrt-firmware sudowrt]! Based on the initial [[Mesh/WalkThrough]] document, but simplified and specific to supported hardware models.

	~~Instructions on flashing routers (installing) with the sudo mesh firmware, [https://github.com/sudomesh/sudowrt-firmware sudowrt] on supported hardware devices!~~		There will soon be a script for flashing based on this old [https://github.com/sudomesh/openwrt-to-sudowrt/blob/master/flash_router.sh install.sh (deprecated)]

	There will soon be a script based on this old [https://github.com/sudomesh/openwrt-to-sudowrt/blob/master/flash_router.sh install.sh (deprecated)]

	=Supported Devices=		=Supported Devices=

Matt: /* Supported Devices */ updates intro

2014-05-14T05:15:52Z

Supported Devices: updates intro

← Older revision		Revision as of 22:15, 13 May 2014
Line 1:		Line 1:
	Instructions on flashing routers with the sudo mesh firmware, [https://github.com/sudomesh/sudowrt-firmware sudowrt]!		Instructions on flashing routers with the sudo mesh firmware, [https://github.com/sudomesh/sudowrt-firmware sudowrt]!

	~~==Supported Devices==~~		Instructions on flashing routers (installing) with the sudo mesh firmware, [https://github.com/sudomesh/sudowrt-firmware sudowrt] on supported hardware devices!

	~~===Ubiquiti===~~		There will soon be a script based on this old [https://github.com/sudomesh/openwrt-to-sudowrt/blob/master/flash_router.sh install.sh (deprecated)]

	====PicoStation====		=Supported Devices=

			==Ubiquiti==

			===PicoStation===

	# Download firmware from http://build.sudomesh.org:8080/latest_images/atheros/openwrt-atheros-ubnt2-pico2-jffs2-128k.bin		# Download firmware from http://build.sudomesh.org:8080/latest_images/atheros/openwrt-atheros-ubnt2-pico2-jffs2-128k.bin
Line 40:		Line 44:
	#* Now your node is ready to be configured. Bring it to [[Sudoroom\|sudo room]] to configure your node using the build server!		#* Now your node is ready to be configured. Bring it to [[Sudoroom\|sudo room]] to configure your node using the build server!

	====NanoStation====		===Bullet===

			===NanoStation===

	====NanoBridge====		===NanoBridge===

Matt: /* PicoStation */ updates with full instructions

2014-05-14T05:08:40Z

PicoStation: updates with full instructions

@@ Line 11: / Line 11: @@
 #** <code>jffs</code> is a read/write filesystem, unlike read-only <code>squashfs</code>
 #** These images are built by openwrt, and we think the 64k and 128k refer to block-size, but it doesn't seem to matter either way.
-#* '''Troubleshooting:''' If you're trying to accessing this site at sudo room, just use the <code>sudo room</code> SSID wifi and not the <code>peoplesopen.net</code> access point. It's a long story.
+#* '''Troubleshooting:''' If you're trying to access this site at sudo room, just use the <code>sudoroom</code> SSID wifi and not the <code>peoplesopen.net</code> access point. It's a long story.
+# Perform a manual reset, enter TFTP mode
 ====NanoStation====
 ====NanoBridge====

Matt: adds first step and structure

2014-05-14T02:36:30Z

adds first step and structure

New page

Instructions on flashing routers with the sudo mesh firmware, [https://github.com/sudomesh/sudowrt-firmware sudowrt]!

==Supported Devices==

===Ubiquiti===

====PicoStation====

# Download firmware from http://build.sudomesh.org:8080/latest_images/atheros/openwrt-atheros-ubnt2-pico2-jffs2-128k.bin
#* There are additional options at http://build.sudomesh.org:8080/latest_images/atheros/ but you probably want <code>openwrt-atheros-ubnt2-pico2-jffs2-128k.bin</code>
#** <code>jffs</code> is a read/write filesystem, unlike read-only <code>squashfs</code>
#** These images are built by openwrt, and we think the 64k and 128k refer to block-size, but it doesn't seem to matter either way.
#* '''Troubleshooting:''' If you're trying to accessing this site at sudo room, just use the <code>sudo room</code> SSID wifi and not the <code>peoplesopen.net</code> access point. It's a long story.
#

====NanoStation====

====NanoBridge====