Omnindoor - Revision history

Jerkey at 21:05, 20 November 2024

2024-11-20T21:05:01Z

← Older revision		Revision as of 14:05, 20 November 2024
Line 3:		Line 3:
	\|+ Caption text		\|+ Caption text
	\|-		\|-
	\| Pin \|\| thing \|\| Mode in Tasmota Configure Unit menu		\| Pin \|\| thing \|\| Mode in Tasmota Configure Unit menu \|\| connection
	\|-		\|-
	\| 4 \|\| lock \|\| Relay 1		\| 4 \|\| lock \|\| Relay 1 \|\| controls the motor lock-direction relay
	\|-		\|-
	\| 32 \|\| unlock \|\| Relay 2		\| 32 \|\| unlock \|\| Relay 2 \|\| controls the motor unlock-direction relay
	\|-		\|-
	\| 33 \|\| current \|\| ADC Current 1		\| 33 \|\| current \|\| ADC Current 1 \|\| measures the voltage of motor shunt resistor
	\|-		\|-
	\| 36 \|\| battery voltage \|\| ADC Current 2		\| 36 \|\| battery voltage \|\| ADC Current 2 \|\| battery voltage minus 3x6.2v zeners, 10KΩ to 5.1KΩ resistor divider
	\|}		\|}

Line 26:		Line 26:
	(100 is too low, limit sometimes trips before motor starts moving, 200 is a lot)		(100 is too low, limit sometimes trips before motor starts moving, 200 is a lot)

	set the adc range https://tasmota.github.io/docs/ADC/ (~~note~~: mode 6 is ADC Range, but 33 is what the software returns for some reason, so we just set 33)		set the adc range https://tasmota.github.io/docs/ADC/ (note1: mode 6 is ADC Range, but 33 is what the software returns for some reason, so we just set 33. note2: these numbers are not calibrate to any actual current or voltage scales, just random numbers)
	AdcParam1 33, 0, 4095, 0, 100		AdcParam1 33, 0, 4095, 0, 100
	AdcParam2 36, 0, 4095, 0, 3.3		AdcParam2 36, 0, 4095, 0, 3.3
Line 36:		Line 36:
	CMD: rule3		CMD: rule3
	RSL: RESULT = {"Rule3":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":40,"Free":471,"Rules":"ON ANALOG#Voltage1>80 DO Power1 0 ENDON"}}		RSL: RESULT = {"Rule3":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":40,"Free":471,"Rules":"ON ANALOG#Voltage1>80 DO Power1 0 ENDON"}}
	CMD: ~~adcparam~~		CMD: adcparam1
	RSL: RESULT = {"AdcParam1":[33,0,4095,0,100]}		RSL: RESULT = {"AdcParam1":[33,0,4095,0,100]}

	"The ESP32 board has four ADC GPIO pins available (gpio34, gpio35, gpio36, gpio39) which can be used for analog inputs. These can be used to read voltage at the ADC pin or to read the module supply voltage (VCC). All analog input pins support 3.3V."		"The ESP32 board has four ADC GPIO pins available (gpio34, gpio35, gpio36, gpio39) which can be used for analog inputs. These can be used to read voltage at the ADC pin or to read the module supply voltage (VCC). All analog input pins support 3.3V."

Jerkey at 08:56, 20 November 2024

2024-11-20T08:56:27Z

← Older revision		Revision as of 01:56, 20 November 2024
Line 9:		Line 9:
	\| 32 \|\| unlock \|\| Relay 2		\| 32 \|\| unlock \|\| Relay 2
	\|-		\|-
	\| 33 \|\| current \|\| ADC ~~Range~~ 1		\| 33 \|\| current \|\| ADC Current 1
	\|-		\|-
	\| ~~Example~~ \|\| ~~Example~~		\| 36 \|\| battery voltage \|\| ADC Current 2
	\|}		\|}

Line 28:		Line 28:
	set the adc range https://tasmota.github.io/docs/ADC/ (note: mode 6 is ADC Range, but 33 is what the software returns for some reason, so we just set 33)		set the adc range https://tasmota.github.io/docs/ADC/ (note: mode 6 is ADC Range, but 33 is what the software returns for some reason, so we just set 33)
	AdcParam1 33, 0, 4095, 0, 100		AdcParam1 33, 0, 4095, 0, 100
			AdcParam2 36, 0, 4095, 0, 3.3

	in the console (or by curl) you can view the rules and adcparam		in the console (or by curl) you can view the rules and adcparam
Line 37:		Line 38:
	CMD: adcparam		CMD: adcparam
	RSL: RESULT = {"AdcParam1":[33,0,4095,0,100]}		RSL: RESULT = {"AdcParam1":[33,0,4095,0,100]}

			"The ESP32 board has four ADC GPIO pins available (gpio34, gpio35, gpio36, gpio39) which can be used for analog inputs. These can be used to read voltage at the ADC pin or to read the module supply voltage (VCC). All analog input pins support 3.3V."

Jerkey at 20:00, 7 October 2024

2024-10-07T20:00:30Z

← Older revision		Revision as of 13:00, 7 October 2024
Line 26:		Line 26:
	(100 is too low, limit sometimes trips before motor starts moving, 200 is a lot)		(100 is too low, limit sometimes trips before motor starts moving, 200 is a lot)

	set the adc range		set the adc range https://tasmota.github.io/docs/ADC/ (note: mode 6 is ADC Range, but 33 is what the software returns for some reason, so we just set 33)
	AdcParam1 33, 0, 4095, 0, 100		AdcParam1 33, 0, 4095, 0, 100

Jerkey at 07:01, 7 October 2024

2024-10-07T07:01:55Z

← Older revision		Revision as of 00:01, 7 October 2024
Line 5:		Line 5:
	\| Pin \|\| thing \|\| Mode in Tasmota Configure Unit menu		\| Pin \|\| thing \|\| Mode in Tasmota Configure Unit menu
	\|-		\|-
	\| 4 \|\| ~~forward~~ \|\| Relay 1		\| 4 \|\| lock \|\| Relay 1
	\|-		\|-
	\| 32 \|\| ~~reverse~~ \|\| Relay 2		\| 32 \|\| unlock \|\| Relay 2
	\|-		\|-
	\| 33 \|\| current \|\| ADC ~~Voltage~~ 1		\| 33 \|\| current \|\| ADC Range 1
	\|-		\|-
	\| Example \|\| Example		\| Example \|\| Example
Line 22:		Line 22:
	Rule2 ON Power2#state=1 DO backlog Delay 50; Power2 0 ENDON		Rule2 ON Power2#state=1 DO backlog Delay 50; Power2 0 ENDON
	rule2 1		rule2 1
	Rule3 ON ANALOG#Voltage1>~~150~~ DO Power1 0; Power2 0 ENDON		Rule3 ON ANALOG#Voltage1>80 DO Power1 0; Power2 0 ENDON
	rule3 1		rule3 1
	(100 is too low, limit sometimes trips before motor starts moving, 200 is a lot)		(100 is too low, limit sometimes trips before motor starts moving, 200 is a lot)

	set the adc range		set the adc range
	~~AdcParam~~ 33, 0, 4095, 0, ~~1024~~		AdcParam1 33, 0, 4095, 0, 100

	in the console (or by curl) you can view the rules and adcparam		in the console (or by curl) you can view the rules and adcparam
Line 34:		Line 34:
	RSL: RESULT = {"Rule1":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":54,"Free":457,"Rules":"ON Power1#state=1 DO backlog Delay 100; Power1 0 ENDON"}}		RSL: RESULT = {"Rule1":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":54,"Free":457,"Rules":"ON Power1#state=1 DO backlog Delay 100; Power1 0 ENDON"}}
	CMD: rule3		CMD: rule3
	RSL: RESULT = {"Rule3":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":40,"Free":471,"Rules":"ON ANALOG#Voltage1>~~100~~ DO Power1 0 ENDON"}}		RSL: RESULT = {"Rule3":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":40,"Free":471,"Rules":"ON ANALOG#Voltage1>80 DO Power1 0 ENDON"}}
	CMD: adcparam		CMD: adcparam
	RSL: RESULT = {"AdcParam1":[33,0,4095,0,~~1024~~]}		RSL: RESULT = {"AdcParam1":[33,0,4095,0,100]}

Jerkey at 02:48, 5 October 2024

2024-10-05T02:48:37Z

← Older revision		Revision as of 19:48, 4 October 2024
Line 20:		Line 20:
	Rule1 ON Power1#state=1 DO backlog Delay 50; Power1 0 ENDON		Rule1 ON Power1#state=1 DO backlog Delay 50; Power1 0 ENDON
	rule1 1		rule1 1
	~~Rule3~~ ON Power2#state=1 DO backlog Delay 50; Power2 0 ENDON		Rule2 ON Power2#state=1 DO backlog Delay 50; Power2 0 ENDON
			rule2 1
			Rule3 ON ANALOG#Voltage1>150 DO Power1 0; Power2 0 ENDON
	rule3 1		rule3 1
	~~Rule2 ON ANALOG#Voltage1>150 DO Power1 0; Power2 0 ENDON~~
	~~rule2 1~~
	(100 is too low, limit sometimes trips before motor starts moving, 200 is a lot)		(100 is too low, limit sometimes trips before motor starts moving, 200 is a lot)

Line 33:		Line 33:
	CMD: rule1		CMD: rule1
	RSL: RESULT = {"Rule1":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":54,"Free":457,"Rules":"ON Power1#state=1 DO backlog Delay 100; Power1 0 ENDON"}}		RSL: RESULT = {"Rule1":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":54,"Free":457,"Rules":"ON Power1#state=1 DO backlog Delay 100; Power1 0 ENDON"}}
	CMD: ~~rule2~~		CMD: rule3
	RSL: RESULT = {"~~Rule2~~":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":40,"Free":471,"Rules":"ON ANALOG#Voltage1>100 DO Power1 0 ENDON"}}		RSL: RESULT = {"Rule3":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":40,"Free":471,"Rules":"ON ANALOG#Voltage1>100 DO Power1 0 ENDON"}}
	CMD: adcparam		CMD: adcparam
	RSL: RESULT = {"AdcParam1":[33,0,4095,0,1024]}		RSL: RESULT = {"AdcParam1":[33,0,4095,0,1024]}

Jerkey at 20:00, 4 October 2024

2024-10-04T20:00:13Z

← Older revision		Revision as of 13:00, 4 October 2024
Line 14:		Line 14:
	\|}		\|}

	curl -u "admin:password" http://10.111/cm?cmnd=~~POWER1+off~~		curl -u "admin:password" http://10.111/cm?cmnd=power1+1

	~~curl -u "admin:password" http://10.111/cm?cmnd=rule1~~+1

	rules so that motor direction gets activated, with a timeout. But if current limit hits, then cancel		rules so that motor direction gets activated, with a timeout. But if current limit hits, then cancel

	Rule1 ON Power1#state=1 DO backlog Delay 30; Power1 0 ENDON		Rule1 ON Power1#state=1 DO backlog Delay 50; Power1 0 ENDON
	rule1 1		rule1 1
	Rule3 ON Power2#state=1 DO backlog Delay 30; Power2 0 ENDON		Rule3 ON Power2#state=1 DO backlog Delay 50; Power2 0 ENDON
	rule3 1		rule3 1
	Rule2 ON ANALOG#Voltage1>~~100~~ DO Power1 0; Power2 0 ENDON		Rule2 ON ANALOG#Voltage1>150 DO Power1 0; Power2 0 ENDON
	rule2 1		rule2 1
			(100 is too low, limit sometimes trips before motor starts moving, 200 is a lot)

	set the adc range		set the adc range
	AdcParam 6, 0, 4095, 0, 1024		AdcParam 33, 0, 4095, 0, 1024

	in the console you can view the rules:		in the console (or by curl) you can view the rules and adcparam

	CMD: rule1		CMD: rule1

Jerkey at 03:20, 4 October 2024

2024-10-04T03:20:51Z

← Older revision		Revision as of 20:20, 3 October 2024
Line 5:		Line 5:
	\| Pin \|\| thing \|\| Mode in Tasmota Configure Unit menu		\| Pin \|\| thing \|\| Mode in Tasmota Configure Unit menu
	\|-		\|-
	\| 4 \|\| forward \|\| ~~Power~~		\| 4 \|\| forward \|\| Relay 1
	\|-		\|-
	\| 14 \|\| reverse \|\| ~~Power~~		\| 32 \|\| reverse \|\| Relay 2
	\|-		\|-
	\| 33 \|\| current \|\| ADC ~~Current (bottom of list)~~		\| 33 \|\| current \|\| ADC Voltage 1
	\|-		\|-
	\| Example \|\| Example		\| Example \|\| Example

Jerkey at 03:12, 4 October 2024

2024-10-04T03:12:09Z

← Older revision		Revision as of 20:12, 3 October 2024
Line 1:		Line 1:
	[[File:Omnindoor-ESP32-wiring.png\|thumb]]		[[File:Omnindoor-ESP32-wiring.png\|thumb]]

	{\| class="wikitable"		{\| class="wikitable"
	\|+ Caption text		\|+ Caption text
	\|-
	~~! Header text !! Header text~~
	\|-		\|-
	\| Pin \|\| thing \|\| Mode in Tasmota Configure Unit menu		\| Pin \|\| thing \|\| Mode in Tasmota Configure Unit menu
Line 13:		Line 10:
	\|-		\|-
	\| 33 \|\| current \|\| ADC Current (bottom of list)		\| 33 \|\| current \|\| ADC Current (bottom of list)
	\|-
	~~\| Example \|\| Example~~
	\|-
	~~\| Example \|\| Example~~
	\|-		\|-
	\| Example \|\| Example		\| Example \|\| Example
	\|}		\|}

			curl -u "admin:password" http://10.111/cm?cmnd=POWER1+off

	~~{"POWER1":"ON"}0jake@eg:~/sketchbook/omnindoor$ curl -u "admin:password" http://10.111/cm?cmnd=POWER1+off~~		curl -u "admin:password" http://10.111/cm?cmnd=rule1+1

	~~{"POWER1":"OFF"}0jake@eg:~/sketchbook/omnindoor$~~ curl -u "admin:password" http://10.111/cm?cmnd=rule1+1

	~~{"Rule1":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":0,"Free":511,"Rules":""}}~~

	~~turn off when limit current hit~~
	~~Rule1 ON Power1#state=1 DO backlog Delay 30; Power1 0 ENDON~~
	~~rule1~~ 1

	~~Rule2 ON ANALOG#Voltage1>100 DO Power1 0 ENDON~~		rules so that motor direction gets activated, with a timeout. But if current limit hits, then cancel
	~~rule2 1~~

	~~set the adc range~~		Rule1 ON Power1#state=1 DO backlog Delay 30; Power1 0 ENDON
			rule1 1
			Rule3 ON Power2#state=1 DO backlog Delay 30; Power2 0 ENDON
			rule3 1
			Rule2 ON ANALOG#Voltage1>100 DO Power1 0; Power2 0 ENDON
			rule2 1

	AdcParam 6, 0, 4095, 0, 1024		set the adc range
			AdcParam 6, 0, 4095, 0, 1024

	in the console you can view the rules:		in the console you can view the rules:

	CMD: rule1		CMD: rule1
			RSL: RESULT = {"Rule1":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":54,"Free":457,"Rules":"ON Power1#state=1 DO backlog Delay 100; Power1 0 ENDON"}}
	RSL: RESULT = {"Rule1":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":54,"Free":457,"Rules":"ON Power1#state=1 DO backlog Delay 100; Power1 0 ENDON"}}		CMD: rule2
			RSL: RESULT = {"Rule2":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":40,"Free":471,"Rules":"ON ANALOG#Voltage1>100 DO Power1 0 ENDON"}}
	CMD: rule2		CMD: adcparam
			RSL: RESULT = {"AdcParam1":[33,0,4095,0,1024]}
	RSL: RESULT = {"Rule2":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":40,"Free":471,"Rules":"ON ANALOG#Voltage1>100 DO Power1 0 ENDON"}}

	CMD: adcparam

	RSL: RESULT = {"AdcParam1":[33,0,4095,0,1024]}

Jerkey at 02:52, 4 October 2024

2024-10-04T02:52:35Z

← Older revision		Revision as of 19:52, 3 October 2024
Line 48:		Line 48:

	RSL: RESULT = {"Rule2":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":40,"Free":471,"Rules":"ON ANALOG#Voltage1>100 DO Power1 0 ENDON"}}		RSL: RESULT = {"Rule2":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":40,"Free":471,"Rules":"ON ANALOG#Voltage1>100 DO Power1 0 ENDON"}}

			CMD: adcparam

			RSL: RESULT = {"AdcParam1":[33,0,4095,0,1024]}

Jerkey at 02:51, 4 October 2024

2024-10-04T02:51:16Z

← Older revision		Revision as of 19:51, 3 October 2024
Line 29:		Line 29:

	turn off when limit current hit		turn off when limit current hit
			Rule1 ON Power1#state=1 DO backlog Delay 30; Power1 0 ENDON
			rule1 1

	Rule2 ON ANALOG#Voltage1>100 DO Power1 0 ENDON		Rule2 ON ANALOG#Voltage1>100 DO Power1 0 ENDON
			rule2 1

	set the adc range		set the adc range

	AdcParam 6, 0, 4095, 0, 1024		AdcParam 6, 0, 4095, 0, 1024

			in the console you can view the rules:

			CMD: rule1

			RSL: RESULT = {"Rule1":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":54,"Free":457,"Rules":"ON Power1#state=1 DO backlog Delay 100; Power1 0 ENDON"}}

			CMD: rule2

			RSL: RESULT = {"Rule2":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":40,"Free":471,"Rules":"ON ANALOG#Voltage1>100 DO Power1 0 ENDON"}}