Difference between revisions of "Beagle Bone Black"

From Sudo Room
Jump to: navigation, search
(Configuring B.A.T.M.A.N to Mesh with Sudo Mesh)
 
Line 37: Line 37:
 
'''Mesh the planet...'''
 
'''Mesh the planet...'''
 
=Configuring B.A.T.M.A.N to Mesh with Sudo Mesh=  
 
=Configuring B.A.T.M.A.N to Mesh with Sudo Mesh=  
This tutorial assumes that you have your Beagle Bone configured running Debian Wheezy.  
+
This tutorial assumes that you have your Beagle Bone configured running Debian Wheezy. It is all recommended that you disabel network-manager.  
  
 +
 +
Add batman module to the kernel
 
<pre>
 
<pre>
 
 
modprobe batman-adv
 
modprobe batman-adv
 +
</pre>
 +
Add B.A.T.M.A.N interface
 +
<pre>
 
batctl if add eth0
 
batctl if add eth0
 +
</pre>
 +
Disable Wifi
 +
<pre>
 
ifconfig wlan0 down
 
ifconfig wlan0 down
 +
</pre>
 +
Set MTU
 +
<pre>
 
ifconfig wlan0 mtu 1532
 
ifconfig wlan0 mtu 1532
iwconfig wlan0 mode ad-hoc essid pplsopen.net-node2node \
+
</pre>
ap CA:FE:C0:DE:F0:0D channel 11
+
Turn on Ad-Hoc Mode and connect to the SSID ppslopen.net-node2node with the Mac Address CA:FE:C0:DE:F0:0D on Channel 11
 +
<pre>
 +
iwconfig wlan0 mode ad-hoc essid pplsopen.net-node2node ap CA:FE:C0:DE:F0:0D channel 11
 +
</pre>
 +
Connect B.A.T.M.A.N interface to Wlan
 +
<pre>
 
batctl if add wlan0
 
batctl if add wlan0
 +
</pre>
 +
Turn on wlan0 and bat0 interfaces
 +
<pre>
 
ifconfig wlan0 up
 
ifconfig wlan0 up
 
ifconfig bat0 up
 
ifconfig bat0 up
 +
</pre>
 +
Connect to your network. Subject to change depending on our network's subnet
 +
<pre>
 
ifconfig bat0 10.200.8.1
 
ifconfig bat0 10.200.8.1
 
route add default gw 10.0.99.1
 
route add default gw 10.0.99.1
 +
</pre>
 +
Enable Port Forwarding
 +
<pre>
 
echo 1 > /proc/sys/net/ipv4/ip_forward  
 
echo 1 > /proc/sys/net/ipv4/ip_forward  
 
 
</pre>
 
</pre>

Latest revision as of 21:22, 17 June 2014

See Also: Mesh/Hardware Fourth Milestone

notes about BBB - Beagle Bone Black

OS Install

OpenWRT

Adafruit tutorial

https://learn.adafruit.com/beaglebone-black-installing-operating-systems/angstrom


first light

Just booting up...

using an FTDI device plugged into J1 pins

find the serial port for the FTDI USB adapter

ls /dev/tty*
  • might be /dev/ttyAMA0 on linux
  • might be /dev/tty.usbmodemfa133 on mac

Wiring from the FTDI device:

  • BBB - FTDI
  • pin 1 GND - GND
  • pin 4 RX - TX
  • pin 5 TX - RX

in terminal:

screen <usbdevicename> 115200
  • first login with root, no password




Mesh the planet...

Configuring B.A.T.M.A.N to Mesh with Sudo Mesh

This tutorial assumes that you have your Beagle Bone configured running Debian Wheezy. It is all recommended that you disabel network-manager.


Add batman module to the kernel

modprobe batman-adv

Add B.A.T.M.A.N interface

batctl if add eth0

Disable Wifi

ifconfig wlan0 down

Set MTU

ifconfig wlan0 mtu 1532

Turn on Ad-Hoc Mode and connect to the SSID ppslopen.net-node2node with the Mac Address CA:FE:C0:DE:F0:0D on Channel 11

iwconfig wlan0 mode ad-hoc essid pplsopen.net-node2node ap CA:FE:C0:DE:F0:0D channel 11

Connect B.A.T.M.A.N interface to Wlan

batctl if add wlan0

Turn on wlan0 and bat0 interfaces

ifconfig wlan0 up
ifconfig bat0 up

Connect to your network. Subject to change depending on our network's subnet

ifconfig bat0 10.200.8.1
route add default gw 10.0.99.1

Enable Port Forwarding

echo 1 > /proc/sys/net/ipv4/ip_forward