625
edits
Difference between revisions of "Mesh/WalkThrough"
→Configure: massive overhaul to simplify and make more clear
(→Configure: massive overhaul to simplify and make more clear) |
|||
| Line 106: | Line 106: | ||
= Configure = | = Configure = | ||
A freshly flashed node automatically sets its IP address to 172.30.0.xx. You will need to configure your laptop to use the following network settings to communicate with the node: | A freshly flashed node automatically sets its IP address to <code>172.30.0.xx</code>. You will need to configure your laptop to use the following network settings to communicate with the node: | ||
* IP address: 172.30.0.10 | * IP address: <code>172.30.0.10</code> | ||
* Subnet mask: 255.255.255.0 | * Subnet mask: <code>255.255.255.0</code> | ||
* Gateway: 0.0.0.0 | * Gateway: <code>0.0.0.0</code> | ||
Or use the commands | Or use the commands | ||
| Line 117: | Line 117: | ||
sudo ip link set <eth_interface> up | sudo ip link set <eth_interface> up | ||
where <eth_interface> is the name of your ethernet interface found using | where <code><eth_interface></code> is the name of your ethernet interface found using <code>ip addr</code> (common names include <code>eth0</code>, <code>enp3s0</code>, ...) | ||
See Network Configuration Guides: [https://sudoroom.org/wiki/Mesh/Network%20Configuration%20for%20Linux Linux] [https://sudoroom.org/wiki/Mesh/Network%20Configuration%20for%20MacOS%20X Mac] | See Network Configuration Guides: [https://sudoroom.org/wiki/Mesh/Network%20Configuration%20for%20Linux Linux] [https://sudoroom.org/wiki/Mesh/Network%20Configuration%20for%20MacOS%20X Mac] | ||
== Autoconf (v.0.3.0) == | == Autoconf (v.0.3.0) == | ||
'''''Note: If you installed | '''''Note: If you installed [https://github.com/sudomesh/sudowrt-firmware/releases/tag/0.3.0 release 0.3.0] for myNet N600 routers, your node can be autoconfigured. You will not need to use the previous solution <code>makenode</code>, otherwise you may need to read the ([[#Makenode_.28v.0.2.3_and_earlier.29|instructions further down]])''''' | ||
[[File:Nodeports titles.png|400px|thumb|right|Plug into port 3 to access the private network from your laptop. Port 2 connects to the public 'peoplesopen.net' network]] Connect your newly-flashed MyNet N600 to your existing Internet router via ethernet from your existing router's LAN port to your new node's Internet port. Wait | [[File:Nodeports titles.png|400px|thumb|right|Plug into port 3 to access the private network from your laptop. Port 2 connects to the public 'peoplesopen.net' network]] | ||
# Connect your newly-flashed MyNet N600 to your existing Internet router via ethernet cable from your existing router's '''LAN port''' to your new node's '''Internet port'''. | |||
# Wait several minutes for your new node autoconfigure, connect to the Internet, and obtain its private IP address from the sudo mesh build server. | |||
#* The node should broadcast several WiFi networks with the following SSIDs and purposes: | |||
#** <code>peoplesopen.net</code> - This is the public network broadcast on the 2.4ghz band; it has no password, and is suitable for access to the internet. | |||
#** <code>peoplesopen.net fast</code> - This is the same public network, but broadcast on the 5ghz band, which is more ideal for high-bandwidth activities such as streaming media. | |||
#** <code>peoplesopen.net-node2node</code> - This is the public network used for mesh nodes to discover and communicate with one another. You should not need to connect or use this network, but you will want to verify it is active. | |||
#** <code>pplsopen-admin</code> This is the private network, and you can use it to access a web dashboard to configure some settings, such as its SSID. The default WiFi password is <code>meshtheworld</code>. Try connecting to it (you can also connect to the private network using an ethernet cable connected to '''port 3''' on an N600 -- see diagram for details). | |||
Learn more about the [[Mesh/Network topology|network's topology here]. | |||
While connected to the ''private'' network, try connecting to the home node's web dashboard by opening a web browser and navigating to http://172.30.0.1 | == Configuring the Web Dashboard == | ||
While connected to the ''private'' network (default <code>pplsopen-admin</code>), try connecting to the home node's web dashboard by opening a web browser and navigating to [http://172.30.0.1] | |||
If the flash was successful you should be brought to the following screen: | If the flash was successful you should be brought to the following screen: | ||
| Line 134: | Line 143: | ||
[[File:Peoplesopen-dash.jpg|frame|center|upright=2]] | [[File:Peoplesopen-dash.jpg|frame|center|upright=2]] | ||
The default password is | The default password is <code>meshtheplanet</code>. | ||
Here you can set the amount of downstream and upstream bandwidth you're willing to share on the public <code>peoplesopen.net</code> network (default is set to 4096kb, or roughly 4 megabits/second): | |||
[[File:homeScreen.jpg|frame|center|upright=2]] | [[File:homeScreen.jpg|frame|center|upright=2]] | ||
[[File:WifiSettings.jpg|frame|left|upright=2|Set your private SSID and password via the 'WIFi Settings' tab. NOTE: When you first set your private SSID name and hit 'Save', you will have to reconnect to the newly-named SSID using the original default password ( | [[File:WifiSettings.jpg|frame|left|upright=2|Set your private SSID and password via the 'WIFi Settings' tab. NOTE: When you first set your private SSID name and hit 'Save', you will have to reconnect to the newly-named SSID using the original default password (<code>meshtheworld</code>) and then reconnect again with the new password after setting it in the dashboard]] [[File:newrouter.png|frame|right|upright=2|See all devices connected to your node via the 'Connections' tab]] | ||
<br clear=all> | <br clear=all> | ||
'''''Note: If you would like to be able to change | == Changing Admin and Root User Passwords == | ||
'''''Note: If you would like to be able to change the above wifi settings in the future, or ssh into your router, you will need to change the admin and root passwords within 12 hours.''''' | |||
To do so, open a terminal while connected to the | To do so, open a terminal while connected to the <code>pplsopen-admin</code> private network (or whatever new SSID you may have chosen): | ||
ssh root@172.30.0.1 | ssh root@172.30.0.1 | ||
Enter the following password: meshtheplanet | Enter the following password: <code>meshtheplanet</code> | ||
Set the root password. | Set the root password. | ||