Difference between revisions of "Omnindoor"

Omnindoor (view source)

Revision as of 19:12, 3 October 2024

113 bytes removed , 3 October

no edit summary

Jerkey

Bureaucrats, Interface administrators, Administrators, Widget editors

311

edits

@@ Line 1: / Line 1: @@
 [[File:Omnindoor-ESP32-wiring.png|thumb]]
 {| class="wikitable"
 |+ Caption text
-|-
-! Header text !! Header text
 |-
 | Pin || thing || Mode in Tasmota Configure Unit menu
@@ Line 13: / Line 10: @@
 |-
 | 33 || current || ADC Current (bottom of list)
-|-
-| Example || Example
-|-
-| Example || Example
 |-
 | Example || Example
 |}
+ curl -u "admin:password" http://10.111/cm?cmnd=POWER1+off
-{"POWER1":"ON"}0jake@eg:~/sketchbook/omnindoor$ curl -u "admin:password" http://10.111/cm?cmnd=POWER1+off
+ curl -u "admin:password" http://10.111/cm?cmnd=rule1+1
-{"POWER1":"OFF"}0jake@eg:~/sketchbook/omnindoor$ curl -u "admin:password" http://10.111/cm?cmnd=rule1+1
-{"Rule1":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":0,"Free":511,"Rules":""}}
-turn off when limit current hit
-Rule1 ON Power1#state=1 DO backlog Delay 30; Power1 0 ENDON
-rule1 1
-Rule2 ON ANALOG#Voltage1>100 DO Power1 0 ENDON
+rules so that motor direction gets activated, with a timeout.  But if current limit hits, then cancel
-rule2 1
-set the adc range
+ Rule1 ON Power1#state=1 DO backlog Delay 30; Power1 0 ENDON
+ rule1 1
+ Rule3 ON Power2#state=1 DO backlog Delay 30; Power2 0 ENDON
+ rule3 1
+ Rule2 ON ANALOG#Voltage1>100 DO Power1 0; Power2 0 ENDON
+ rule2 1
-AdcParam 6, 0, 4095, 0, 1024
+ set the adc range
+ AdcParam 6, 0, 4095, 0, 1024
 in the console you can view the rules:
-CMD: rule1
+ CMD: rule1
+ RSL: RESULT = {"Rule1":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":54,"Free":457,"Rules":"ON Power1#state=1 DO backlog Delay 100; Power1 0 ENDON"}}
-RSL: RESULT = {"Rule1":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":54,"Free":457,"Rules":"ON Power1#state=1 DO backlog Delay 100; Power1 0 ENDON"}}
+ CMD: rule2
+ RSL: RESULT = {"Rule2":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":40,"Free":471,"Rules":"ON ANALOG#Voltage1>100 DO Power1 0 ENDON"}}
-CMD: rule2
+ CMD: adcparam
+ RSL: RESULT = {"AdcParam1":[33,0,4095,0,1024]}
-RSL: RESULT = {"Rule2":{"State":"ON","Once":"OFF","StopOnError":"OFF","Length":40,"Free":471,"Rules":"ON ANALOG#Voltage1>100 DO Power1 0 ENDON"}}
-CMD: adcparam
-RSL: RESULT = {"AdcParam1":[33,0,4095,0,1024]}