Difference between revisions of "TAZ 4"
| Line 6: | Line 6: | ||
The extruder head from the TAZ 3 was transferred onto the TAZ 4 which will presumably make a better 3D printer. The TAZ 3 will be converted for solder paste dispensing only | The extruder head from the TAZ 3 was transferred onto the TAZ 4 which will presumably make a better 3D printer. The TAZ 3 will be converted for solder paste dispensing only | ||
The TAZ 4 uses an [https://reprap.org/wiki/Rambo Ultimachine Rambo 1.3L main board] | The TAZ 4 uses an [https://reprap.org/wiki/Rambo Ultimachine Rambo 1.3L main board] and here is the correct [[File:RAMBo_1.3L_Schematic.pdf|RAMBo_1.3L_Schematic]] | ||
[Image:https://reprap.org/wiki/File:Rambo-conn-all.jpg] | [Image:https://reprap.org/wiki/File:Rambo-conn-all.jpg] | ||
The original 14-pin "Extruder 0" connector on the TAZ4 was removed from "Aux Power Mosfet Output" (pins 5/red,6/black), E0 Heat (pins 12,13), E0 Fan (9/black,10/red) and Ground (pin 2), and E0 (3,7,11,14). The extruder harness from the TAZ3 was installed in it. | The original 14-pin "Extruder 0" connector on the TAZ4 was removed from "Aux Power Mosfet Output" (pins 5/red,6/black), E0 Heat (pins 12,13), E0 Fan (9/black,10/red) and Ground (pin 2), and E0 (3,7,11,14). The extruder harness from the TAZ3 was installed in it. | ||
The TAZ 4 didn't work because Fuse F3 on the RAMBO main board was missing. It's supposed to be a [https://www.littelfuse.com/products/fuse-blocks-fuseholders-and-fuse-accessories/fuse-blocks/154.aspx Littelfuse OMNI-BLOK 154 series] and we didn't have any, so I stuck a 5-amp [https://www.digikey.com/en/products/detail/littelfuse-inc/0466005-NR/521341 F1460CT-ND] in there since we have dozens of them in the FUSES bin: [[Image:Taz4_fuse_kludge.jpg|thumb|left]] | |||
And now it turns on and the LCD lights up but i can't get anything to move from the controls. Tune in next week to see what happens. | |||
Revision as of 02:11, 12 June 2022
Sudoroom has a TAZ 4 3d printer, that was donated in 2022. It should not be confused with the older TAZ 3 3d printer, which didn't work very well as a 3D printer.
Documentation for the TAZ 4 from Lulzbot corporation
The extruder head from the TAZ 3 was transferred onto the TAZ 4 which will presumably make a better 3D printer. The TAZ 3 will be converted for solder paste dispensing only
The TAZ 4 uses an Ultimachine Rambo 1.3L main board and here is the correct File:RAMBo 1.3L Schematic.pdf [Image:https://reprap.org/wiki/File:Rambo-conn-all.jpg] The original 14-pin "Extruder 0" connector on the TAZ4 was removed from "Aux Power Mosfet Output" (pins 5/red,6/black), E0 Heat (pins 12,13), E0 Fan (9/black,10/red) and Ground (pin 2), and E0 (3,7,11,14). The extruder harness from the TAZ3 was installed in it.
The TAZ 4 didn't work because Fuse F3 on the RAMBO main board was missing. It's supposed to be a Littelfuse OMNI-BLOK 154 series and we didn't have any, so I stuck a 5-amp F1460CT-ND in there since we have dozens of them in the FUSES bin:
And now it turns on and the LCD lights up but i can't get anything to move from the controls. Tune in next week to see what happens.