[sudo-discuss] kijanigrows microserver in sudoroom

[emaundu]

http://kijanigrows.com/kb/using-1-wire-temperature-sensors-with-the-v2-controller/

it's a one wire ... vcc, gnd, and D6 ... see tutorial above


On 11/30/2016 11:48 PM, Jake wrote:
> can you tell me what pin the temperature sensor is supposed to 
> connect?  It got
> pulled out at some point and was sitting in some random analog pins.  
> the wires
> are in the order RED, BLACK, YELLOW
>
> wow we figured it out, it's very confusing though.  the ethernet port is
> serving DHCP out, but it's using its internal wifi antenna to get on the
> "sudoroom" wifi.
>
> our subnet is 100.*.*.* but I saw the IP address in the json linked 
> from your
> URL below.
>
> does it contain a program to upload to its internal arduino? where's the
> program that's in the arduino now?
>
> thank you for this cool thing.  we want to get it working to log the
> temperature in sudoroom, and maybe even to control a heater!
>
> -jake
>
> On Wed, 30 Nov 2016, emaundu wrote:
>
>> it is active ...
>>
>> http://api.kijanigrows.com/app
>>
>> and here
>>
>> http://api.kijanigrows.com/v2/devices/list
>>
>> and here
>>
>> http://api.kijanigrows.com/v2/maps/list
>>
>>
>>
>> On 11/30/2016 10:23 PM, Jake wrote:
>>> hi Eric,
>>>
>>> we have the controller powered up and plugged into internet, but it 
>>> does not
>>> seem to be updating the page here:
>>> http://api.kijanigrows.com:3000/dashboard/db/sudoroom
>>>
>>> or here
>>>
>>> http://api.kijanigrows.com/app/#/device_sensors/sudoroom/
>>>
>>> it definitely is plugged into ethernet and has a link and it is 
>>> powered on.
>>>
>>> can we check on it somehow?  how does it work?
>>>
>>> it's on the sudoroom hacking table right now, plugged in.  i'm not 
>>> sure if the
>>> sensors are connected right or not.
>>>
>>> thank you!
>>> -jake
>>>
>>> On Wed, 30 Nov 2016, robb wrote:
>>>
>>>> ---------- Forwarded message ----------
>>>> From: emaundu <emaundu at kijanigrows.com>
>>>> Date: Thu, Jun 23, 2016 at 4:15 AM
>>>> Subject: Re: salaams
>>>> To: robb <sf99er at gmail.com>
>>>>
>>>>
>>>> hey robb.
>>>> hope well.
>>>> please could you reset the controller for me ....  i think when i 
>>>> left it
>>>> was not work ..
>>>> please could you reset the power switch (big white button on 
>>>> bottom)... if
>>>> it works it should show data when you select say a last 15min data 
>>>> setting
>>>> in the graphs below
>>>> the power switch maybe sticky/stiff due to the new cardboard i 
>>>> swapped just
>>>> before i left. remove it from the wall where i taped it if need be to
>>>> ensure the button depresses off then on.
>>>> http://api.kijanigrows.com/app#/trends/sudoroom
>>>> or by seeing it's uptime update in this listing
>>>> http://api.kijanigrows.com/v2/devices/list
>>>>
>>>> thanks so very much in advance .. i planned on dropping by 
>>>> yesterday/today
>>>> but did not get a chance ...
>>>> soon,
>>>> -m.
>>>>
>>>>
>>>>
>>>> On 06/16/2016 07:01 AM, robb wrote:
>>>>
>>>> motion sensor lights would be nice
>>>>
>>>> On Thu, Jun 16, 2016 at 4:51 AM, emaundu <emaundu at kijanigrows.com> 
>>>> wrote:
>>>>
>>>>> hey bobby (hope i got that correct - ehh short term memory loss)
>>>>> hope well.
>>>>> nice meeting you earlier on ...
>>>>> what other data points do you think would be nice to collect and 
>>>>> visualize
>>>>> in the sudoroom.
>>>>> thanks,
>>>>> -maundu
>>>>>
>>>>>
>>>>
>>