Difference between revisions of "Mesh/OpenWRT"
| Line 215: | Line 215: | ||
This router has TFTP enabled out of the box. You _must_ set your computer's IP address on ethernet, | This router has TFTP enabled out of the box. You _must_ set your computer's IP address on ethernet, | ||
however, to '192.168.1.15' in order to be able to use a command-line TFTP client. | however, to '192.168.1.15' in order to be able to use a command-line TFTP client. | ||
You may have to hold down the reset button while you plug in the power, and keep it held in for a few seconds after, in order to enableTFTP. | |||
== Meraki mini == | == Meraki mini == | ||
Revision as of 15:01, 4 June 2013
OpenWRT installation
Web interface method
- Power on router and let it boot.
- Press and hold power button for 30 seconds.
- Wait for router to reboot.
- Connect to the access point using LAN.
- Go to web interface, e.g. http://192.168.1.1/
- If this doesn't work, look up the reset method for your specific router.
- Find the firmware upgrade page.
- On your computer, download the firmware.
- Different versions are here.
- The snapshots directory has recent development versions.
- If you have a WRT54G you probably want [1] assuming 12.09 (attitude adjustment) is the most recent stable version.
- If you have an Asus RT-N10+, you probably want [2] assuming 12.09 (attitude adjustment is the most recent stable version.
- Upload the firmware using the web form and wait for the router to reboot.
TFTP method
This requires that the router has a TFTP server enabled. Type these commands with the router powered off, then power on the router and it should work. For some routers (like the Asus RT-N10+) you have to hold down the reset button while you plug in the power, and keep it held in for a few seconds after. For some routers, your laptop must have a specific IP, otherwise the tftp won't work. See the "Router-specific notes" section of this page.
tftp 192.168.1.1 binary rexmt 1 timeout 60 trace tftp> put firmwarefile.bin
If it doesn't work, try omitting the "rexmt 1" line.
Curl method
You may use the command line tool 'curl' on Linux and Mac OS X systems to send files to your router. For instance, to flash the firmware of the Asus R10+ router, using 'curl' instead of tftp, you can issue the following command:
$ curl -T openwrt-ramips-rt305x-rt-n10-plus-squashfs-sysupgrade.bin tftp://192.168.1.1
OpenWRT configuration
Logging in and setting root password
Telnet into the device:
telnet 192.168.1.1
If it asks for a password use 'passwd' (without the quotes).
Set a root password on the router:
passwd
Verify that you can log in using ssh from your computer:
ssh root@192.168.1.1
If you can ssh into the router, disable telnet:
rm /etc/rc.d/S50telnet
Enabling TFTP
Operating Systems: TFTP clients
Debian or debian-based systems (e.g. Ubuntu and Mint)
Install tftp client:
sudo apt-get install tftp
Other GNU/Linux systems
Using whatever your Linux distribution's package management might be, search for an install the tftp client package.
Windows 7/Server 2008
TFTP is disabled by default. In Control Panel > Programs and Features, click on Turn Windows features on or off, find TFTP Client and tick the box. You should now be able to use TFTP from the command prompt
Enabling TFTP on various routers
WRT54G / WRT54GL
If you're on an WRT54G or WRT54GL then you should do this to enable TFTP. If you're not on one of those routers, then don't do it!
It makes it easier to upgrade the firmware and recover from serious problems.
CAUTION: This will reboot your router.
nvram set boot_wait=on nvram set boot_time=10 nvram set wait_time=10 nvram commit && reboot
Enabling wifi
OpenWRT has wifi disabled per default.
vi /etc/config/wireless
Remove the line indicated:
config wifi-device radio0 option type mac80211 option channel 11 option macaddr 00:1c:10:bc:a7:1f option hwmode 11g # REMOVE THIS LINE TO ENABLE WIFI: option disabled 1
Reboot.
Wait a few minutes, then ssh back into the router.
Run 'wifi'. You should see the following:
root@OpenWrt:~# wifi Configuration file: /var/run/hostapd-phy0.conf Using interface wlan0 with hwaddr 00:1c:10:bc:a7:1f and ssid "OpenWrt"
Connecting to wifi
You will need internet access to install packages and other things. Edit your config wifi-iface section to match the example below.
vi /etc/config/wireless
config wifi-iface option device radio0 option network wwan option mode sta option ssid sudoroom option encryption none
If you're on an encrypted network add the following options...
option encryption psk2 option key 1234567890
Next add the "wwan" interface.
vi /etc/config/network
config interface wwan option proto dhcp
Restart networking and you should be set. /etc/init.d/network restart
Installing BATMAN
Online
Use these instructions if your router is connected to the internet:
ssh root@192.168.1.1 opkg update opkg install kmod-batman-adv
Manually / Offline
If your router does not have internet connectivity when installing, then use these instructions.
Download these packages from:
http://downloads.openwrt.org/<openwrt_version_name>/<openwrt_version_number>/<chipset_name>/<type>/packages
Go to http://downloads.openwrt.org and browse to the correct directory. If there are multiple types, you probably want the 'generic' one, but check with the OpenWRT wiki page for your device to make sure.
These are the required packages:
kmod-batman-adv_<version>_<chipset>.ipk kmod-lib-crc16_<version>_<chipset>.ipk
Use scp to copy them to the router:
scp kmod-*.ipk root@192.168.1.1:
Then ssh into the router and install them:
ssh root@192.168.1.1 opkg install kmod-*.ipk
Configuring BATMAN
See Mesh/BATMAN.
Router-specific notes
ARCFlex Freestation 2
The Freestation is based on the 8Devices Carambola board, which interestingly is pretty cheap at 22 euro. We would have to solder an ethernet jack and and antenna and add a case.
- The OpenWRT wiki page for the Freestation
WARNING: The following instructions will leave your router in a state where the serial console is needed to recover.
There seem to be some problems with the OpenWRT Freestation image:
- The main ethernet port is seen by OpenWRT as the WLAN port and will try to get an IP address with DHCP, but the DHCP Discover messages will be tagged with VLAN ID 1, so you have to set up VLAN support and a eth0.1 interface with a DHCP server on your laptop in order to give it an IP.
- Giving it an IP won't help you though, since neither web server nor ssh nor telnet is enabled on the WLAN port.
- The other ethernet port seems to have nothing running on it. Not even a DHCP client. Also, be careful not to plug PoE stuff into your laptop. The PoE passthrough _should_ be disabled per default in OpenWRT, but you never know!
The image to use is the ramips-rt305x. The image we tried was:
openwrt-ramips-rt305x-freestation5-squashfs-sysupgrade.bin
Note that it says freestation5, but works just as well on the Freestation 2. Firmware upgrade happens via the web interface, but you have to rename the file to .img instead of .bin, otherwise it won't be accepted. You may have to upgrade to the newest version of the official Freestation firmware (ARC-OS) before it's possible to upload the OpenWRT firmware file.
Asus RT-N10+
This router has TFTP enabled out of the box. You _must_ set your computer's IP address on ethernet, however, to '192.168.1.15' in order to be able to use a command-line TFTP client.
You may have to hold down the reset button while you plug in the power, and keep it held in for a few seconds after, in order to enableTFTP.
Meraki mini
None of the methods on the openwrt wiki page worked, so I had to resort to using the serial console.
- Open the router (two screws behind the sticker).
- Connect a USB to 3.3v serial adapter to the serial pins.
Serial pins with the antenna pointing away from you and the ethernet port pointing towards you, from left to right:
1: 3.3v 2: TX 3: RX 4: GND
The router may either be using 9600 or 115200 baud. Other settings are 8N1 with software and hardware flow control turned off.
Start minicom with e.g:
minicom -o -D /dev/ttyUSB0
Then configure by hitting ctrl+a followed by an o. Use the arrow keys to select "Serial port setup" and adjust settings. When done, hit escape once or twice to exit the menu. Optionally you can choose to "Save setup as dfl" to save the settings for next time.
When you plug in the router with the serial connected, you should see the following line:
== Executing boot script in 2.000 seconds - enter ^C to abort
Once you see that line, immediately hit ctrl+c.
You will then get a RedBoot prompt like this:
RedBoot>
Leave that sitting in its window for a bit. You'll need it later.
You will now need to set up a tftp server on your computer.
Install the tftp server:
sudo aptitude install tftpd-hpa
Make sure it isn't running with default parameters:
sudo /etc/init.d/tftpd-hpa stop
Download openwrt:
cd mkdir openwrt_for_meraki_mini cd openwrt_for_meraki_mini wget http://downloads.openwrt.org/attitude_adjustment/12.09/atheros/generic/openwrt-atheros-vmlinux.gz wget http://downloads.openwrt.org/attitude_adjustment/12.09/atheros/generic/openwrt-atheros-root.squashfs
You may want to get a different version than attitude adjustment stable. Just make sure you get the two files ending in vmlinux.gz and root.squashfs, and make sure you get them for the atheros chipset.
Ensure that NetworkManager is not managing your network card. The easiest temporary way of doing this is to stop NetworkManager:
sudo /etc/init.d/network-manager stop
Change the IP of your network card to 192.168.84.9:
sudo ifconfig eth0 192.168.84.9 netmask 255.255.255.0 up
cd into the directory where the .gz and .squashfs files are located, then start the tftp server:
sudo in.tftpd -l -L -p --address 192.168.84.9 --secure ./
It doesn't tell you it's been started, it just sits there waiting. You can test that it's working using:
curl tftp://192.168.84.9/openwrt-atheros-vmlinux.gz > /tmp/out.gz
Which should download the .gz file to /tmp/out.gz
Now, go back to the RedBoot console waiting for you in minicom:
Execute the following commands, pressing y when asked questions. The "fis create" commands will take a long time to complete.
RedBoot> ip_address -l 192.168.84.1 -h 192.168.84.9
RedBoot> fis init
RedBoot> load -r -b 0x80041000 -m tftp -h 192.168.84.9 openwrt-atheros-vmlinux.gz
RedBoot> fis create -r 0x80041000 -l 0x180000 -e 0x80041000 linux
RedBoot> load -r -b 0x80041000 -m tftp -h 192.168.84.9 openwrt-atheros-root.squashfs
RedBoot> fis create -r 0x80041000 -l 0x620000 rootfs
RedBoot> fconfig -d boot_script_data
fis load -d linux
exec
RedBoot> reset
Thanks to the Hack Notes blog for the above RedBoot commands.
After the router resets, you should have OpenWRT running in the serial console. Change your IP address again:
sudo ifconfig eth0 192.168.1.100 netmask 255.255.255.0 up
Now you should be able to telnet into the meraki:
telnet 192.168.1.1
If it worked: Hurray!
When you're done, remember to re-enable network manager:
sudo /etc/init.d/network-manager start