Difference between revisions of "Mesh/WalkThrough"

# [[#makenode/Configure|configuring the node]] to function as part of a mesh.

Now that you have a node, you canflash it with the latest sudowrt-firmware. The first step is to download the firmware image file for your supported router. At the moment, we are supporting the following firmware builds:

* IP address: 172.30.0.10

* Subnet mask:  255.255.255.0

* Gateway: 0.0.0.0

Or use the commands

  sudo ip link set <eth_interface> down

  sudo ip addr add 172.30.0.10/24 dev <eth_interface>  

  sudo ip link set <eth_interface> up

 

where <eth_interface> is the name of your ethernet interface found using `ip addr` (common names include eth0, enp3s0, ...)

See Network Configuration Guides: [https://sudoroom.org/wiki/Mesh/Network%20Configuration%20for%20Linux Linux] [https://sudoroom.org/wiki/Mesh/Network%20Configuration%20for%20MacOS%20X Mac]

== Autoconf (v.0.3.0) ==

[[File:Nodeports titles.png|400px|thumb|right|Plug into port 3 to access the private network from your laptop. Port 2 connects to the public 'peoplesopen.net' network]] Connect your newly-flashed MyNet N600 to your existing Internet router via ethernet from your existing router's LAN port to your new node's Internet port. Wait a few minutes for your new node to connect to the Internet and obtain its private IP address. Once this happens, the node will broadcast a new WiFi network starting with 'peoplesopen.net' (and ending with a unique IP address). This is the public network, has no password, and is suitable for day-to-day internet access.

 

There is also a wireless network called 'pplsopen-admin'. This is the private network, and you can use it to access a web dashboard to configure some settings. The default WiFi password is 'meshtheworld'. Try connecting to it (you can also connect to the private network using an ethernet cable connected to port 3 on an N600).

 

While connected to the ''private'' network, try connecting to the home node's web dashboard by opening a web browser and navigating to http://172.30.0.1  

The default password is 'meshtheplanet'.

[[File:WifiSettings.jpg|frame|left|upright=2|Set your private SSID and password via the 'WIFi Settings' tab. NOTE: When you first set your private SSID name and hit 'Save', you will have to reconnect to the newly-named SSID using the original default password ('meshtheworld') and then reconnect again with the new password after setting it in the dashboard]] [[File:newrouter.png|frame|right|upright=2|See all devices connected to your node via the 'Connections' tab]]

'''''Note: If you would like to be able to change these settings in the future, or ssh into your router, you will need to change the admin and root passwords within 12 hours.'''''

To do so, open a terminal while connected to the 'pplsopen-admin' SSID:

Enter the following password: meshtheplanet

== Makenode (v.0.2.3 and earlier) ==

Makenode's documentation has been consolidated to [[Mesh/Makenode|its page.]]

After you're finished with the flashing and configuration, your home node should be available for connections via your private WiFi SSID. Additionally the public SSID 'peoplesopen.net' will be available. It should also be populated on the [https://peoplesopen.herokuapp.com monitor]!

A third interface named 'pplsopen.net-node2node' will be detectable as well. This is the interface used for the nodes to mesh with each other.

At this point you're setup. For more information on using your node, such as accessing the web-based management interface, see [[Home and extender nodes#Home_nodes|Home node info]]

 

For more technical details on the internals of the home node, see the [[Mesh/Technical_Overview]]

 

For more in depth testing procedures, see our [https://github.com/sudomesh/babeld-lab/blob/master/operator_manual.md mesh node operator's manual].