[DisasterRadio] hello
Mitra Ardron
mitra at mitra.biz
Thu Sep 23 18:20:31 PDT 2021
Code
Yes, I meant the one on the video.
3D printing is a totally fine way of doing an enclosure in low
volumes, but is a massive difference in both reality and "cost"
between buying something on Alibaba or just via paypal from someone
who has built them before, and something only available as a CAD/3D
printer file. I've gone through the process of finding a 3D printing
shop, and getting something made, with a less than 50% success rate,
and a one-off is always more expensive as even a good shop has to
allow for the likely cost of getting it wrong the first time.
One of the advantages disaster.radio potentially has over some of
the other solutions its the potential for geek-free setup and
install. I can figure it out, but most of the villages around here -
who could use a setup like disaster radio - don't have a resident
geek, and trying to find a 3D printer to print a one-off certainly
puts it in the needs-a-geek bucket.
The enclosure Sam suggests sounds a better candidate, though it
needs the panel mounted separately.
Sam
I'll try that enclosure you suggest - its a good price. But I'm
wondering, have you tried using one of them with the other parts in
that part list? How did you handle mounting to and getting the
aerial out, Are those connectors the right size for that, without
looking in detail at the components I'm guessing it would want the
small connectors for the solar panel cable but its unclear if the
4-8 or 9-12 connector would be best for the antenna proposed - I
think the smaller (the antenna says 8mm)
On 24/9/21 7:10 am, Code Bus wrote:
> What enclosure are you referring to?
> If you mean the one featured in the video, you're free to make them
> yourself. The design exists as CAD and in 3d printable formats in the
> github repository. It is not less "real" simply because it hasn't been
> mass produced.
>
> Otherwise, like we've suggested, you can follow the Aliexpress parts
> list and make a working device, or use any enclosure designed to
> prevent water ingress.
>
> Sep 23, 2021, 20:46 by mitra at mitra.biz:
>
> Thanks Sam
>
> I was looking at the enclosure shown on the image on
> https://disaster.radio/ and thought that might have been real :-(
>
> - Mitra
>
> On 23/9/21 10:30 pm, sam at bristolwireless.net wrote:
>
> Can you clarify what the current state is - i.e. if I got
> the boards, built a pair of units, and flashed it - then
> would the chat and map apps talk over it.
>
>
> Yes that should be possible. You can buy them pre-flashed if
> you want to miss that step:
> https://www.aliexpress.com/item/4000396836096.html
>
> If using the webapp you only get a chat.
>
> If you use the Android app then you get a chat and a map AFAIK.
>
> By the way ... I notice there is a bad link to the
> enclosure on https://disaster.radio/build/
>
>
> Thx started fixing that link here:
> https://github.com/sudomesh/disaster-radio-website/pull/12
> awaiting someone to approve.
>
> This was the enclosure used:
> https://www.aliexpress.com/item/4000452268197.html
>
> It's fairly obvious how to put it together, but there are some
> instructions here too:
> https://hackaday.io/project/170069-disaster-radio-lora-mesh
>
> Thanks
>
> Sam
>
>
>
> - Mitra
>
>
> On 23/9/21 10:49 am, Code Bus wrote:
>
> The project lacks a maintainer with enough time to
> really give it the care it needs.
> I've been spending my free time trying to modify the
> firmware for the v3 dual-module prototype, it is
> slow-going.
>
> Other LoRa boards seem to work pretty well with the
> firmware in its current state
>
>
> Sep 22, 2021, 20:37 by mitra at mitra.biz:
>
> I tried to find out what was happening with
> Disaster Radio, by
> asking here - got zero responses :-( its really
> hard to figure out
> if there is anything going on that is useful to
> connect with :-(
>
> On 23/9/21 9:48 am, Greg Troxel wrote:
>
> eM Grzegorz<emgrzegorz at interia.pl>
> <mailto:emgrzegorz at interia.pl> writes:
>
> Hi,active list?Grzegorz
>
> Sort of. When people ask, someone answers.
> But not much seems to be
> happening. I do have the impression that those
> on the list wish there'd
> be more activity, and that most of them sort of
> hope to contribute. I
> of course do not speak for the coalition.
>
> Perhaps you can tell us why you're interested
> and what you'd like to see
> as highest priority.
>
>
>
> _______________________________________________
> DisasterRadio mailing list
> DisasterRadio at lists.sudoroom.org
> https://sudoroom.org/lists/listinfo/disasterradio
>
> -- Mitra Ardron -mitra at mitra.biz www.mitra.biz
> <http://www.mitra.biz>
> +61-491-082-515 mobile; +1-510-423-1767 whatsapp
>
>
> _______________________________________________
> DisasterRadio mailing list
> DisasterRadio at lists.sudoroom.org
> https://sudoroom.org/lists/listinfo/disasterradio
>
>
> --
> Mitra Ardron -mitra at mitra.biz www.mitra.biz
> +61-491-082-515 mobile; +1-510-423-1767 whatsapp
>
>
>
>
>
> --
> Mitra Ardron - mitra at mitra.biz www.mitra.biz
> +61-491-082-515 mobile; +1-510-423-1767 whatsapp
>
>
--
Mitra Ardron -mitra at mitra.biz www.mitra.biz
+61-491-082-515 mobile; +1-510-423-1767 whatsapp
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://sudoroom.org/pipermail/disasterradio/attachments/20210924/f47c09af/attachment.html>
More information about the DisasterRadio
mailing list