289
edits
(stub page for our new printer!) |
|||
(15 intermediate revisions by 4 users not shown) | |||
Line 1: | Line 1: | ||
[[File:Taz_first_print_2.jpg|right|frameless|460px]] | [[File:Taz_first_print_2.jpg|right|frameless|460px]] | ||
UPDATE: Sudoroom acquired a [[TAZ_4|TAZ4]] in 2022 and [[user:Jerkey]] swapped the extruder out of the TAZ3 onto it, since the TAZ3 would not do a decent print and the TAZ4 looked good but was missing an exturder. The TAZ3 will be converted to [https://github.com/hzeller/rpt2pnp solder paste dispensing] only, as seen [https://hackaday.com/2014/04/02/dispensing-solder-paste-with-a-3d-printer/ here on Hackaday] | |||
Sudoroom has a [https://www.lulzbot.com/products/lulzbot-taz-3-3d-printer TAZ3] 3D printer. We won it in the [https://www.lulzbot.com/ LulzBot] 2014 printer giveaway! It can print from an SD card, with many materials: | Sudoroom has a [https://www.lulzbot.com/products/lulzbot-taz-3-3d-printer TAZ3] 3D printer. We won it in the [https://www.lulzbot.com/ LulzBot] 2014 printer giveaway! It can print from an SD card, with many materials: | ||
Line 9: | Line 11: | ||
We are still getting familiar with this machine, but very excited to hack on it! | We are still getting familiar with this machine, but very excited to hack on it! | ||
=== Manual === | |||
* [http://download.lulzbot.com/TAZ/documentation/current/LulzBot_TAZ-Brochure.pdf TAZ 3.0 Printer brochure PDF] | |||
* [https://download.lulzbot.com/TAZ/3.0/documentation/2013Q4/LulzBot_TAZ_3.0-User_Manual-ebook.pdf TAZ 3.0 User Manual PDF] | |||
=== Hardware === | |||
* [https://reprap.org/wiki/File:Rambo1-2-conn-main.jpg diagram of RAMBO control board] | |||
=== Firmware === | |||
here's a backup of the factory firmware .hex file and "source code" for our TAZ 3: | |||
https://github.com/sudoroom/taz3d | |||
Below are links to the original firmware from the manufacturer's site, AKA the first commits in the above GitHub repo. | |||
here's the factory hex file (which can be flashed using cura-lulzbot) | |||
https://devel.lulzbot.com/TAZ/3.1/software/2014Q2/firmware/marlin/Marlin_taz3.1.cpp.hex | |||
factory firmware source code (Marlin with configuration tweaks): | |||
http://download.lulzbot.com/TAZ/3.1/software/current/firmware/marlin_taz/marlin_taz.tar.bz2 | |||
=== 3D Models === | |||
[https://www.lulzbot.com/support/taz-slic3r-profiles Taz Slic3r Profiles] | |||
=== Links === | |||
* [http://opensourceecology.org/wiki/How_to_print_your_sketchup_model_in_lulzbot_Taz_3d_printer How to print your sketchup model on a lulzbot taz 3d printer] nice clear how-to from open ecology | |||
* [[SudoKit/IndividualKits]] tangible kit project around 3D printing in the works :) | |||
[[Category:3DPrinting]] |