hi Eric, we have the controller powered up and plugged into internet, but it does not seem to be updating the page here: http://api.kijanigrows.com:3000/dashboard/db/sudoroom or here http://api.kijanigrows.com/app/#/device_sensors/sudoroom/ it definitely is plugged into ethernet and has a link and it is powered on. can we check on it somehow? how does it work? it's on the sudoroom hacking table right now, plugged in. i'm not sure if the sensors are connected right or not. thank you! -jake On Wed, 30 Nov 2016, robb wrote: > ---------- Forwarded message ---------- > From: emaundu <emaundu(a)kijanigrows.com> > Date: Thu, Jun 23, 2016 at 4:15 AM > Subject: Re: salaams > To: robb <sf99er(a)gmail.com> > > > hey robb. > hope well. > please could you reset the controller for me .... i think when i > left it > was not work .. > please could you reset the power switch (big white button on > bottom)... if > it works it should show data when you select say a last 15min data > setting > in the graphs below > the power switch maybe sticky/stiff due to the new cardboard i > swapped just > before i left. remove it from the wall where i taped it if need be to > ensure the button depresses off then on. > http://api.kijanigrows.com/app#/trends/sudoroom > or by seeing it's uptime update in this listing > http://api.kijanigrows.com/v2/devices/list > > thanks so very much in advance .. i planned on dropping by > yesterday/today > but did not get a chance ... > soon, > -m. > > > > On 06/16/2016 07:01 AM, robb wrote: > > motion sensor lights would be nice > > On Thu, Jun 16, 2016 at 4:51 AM, emaundu <emaundu(a)kijanigrows.com> > wrote: > >> hey bobby (hope i got that correct - ehh short term memory loss) >> hope well. >> nice meeting you earlier on ... >> what other data points do you think would be nice to collect and >> visualize >> in the sudoroom. >> thanks, >> -maundu >> >> >

hi Eric, we have the controller powered up and plugged into internet, but it does not seem to be updating the page here: http://api.kijanigrows.com:3000/dashboard/db/sudoroom or here http://api.kijanigrows.com/app/#/device_sensors/sudoroom/ it definitely is plugged into ethernet and has a link and it is powered on. can we check on it somehow? how does it work? it's on the sudoroom hacking table right now, plugged in. i'm not sure if the sensors are connected right or not. thank you! -jake On Wed, 30 Nov 2016, robb wrote: > ---------- Forwarded message ---------- > From: emaundu <emaundu(a)kijanigrows.com> > Date: Thu, Jun 23, 2016 at 4:15 AM > Subject: Re: salaams > To: robb <sf99er(a)gmail.com> > > > hey robb. > hope well. > please could you reset the controller for me .... i think when i > left it > was not work .. > please could you reset the power switch (big white button on > bottom)... if > it works it should show data when you select say a last 15min data > setting > in the graphs below > the power switch maybe sticky/stiff due to the new cardboard i > swapped just > before i left. remove it from the wall where i taped it if need be to > ensure the button depresses off then on. > http://api.kijanigrows.com/app#/trends/sudoroom > or by seeing it's uptime update in this listing > http://api.kijanigrows.com/v2/devices/list > > thanks so very much in advance .. i planned on dropping by > yesterday/today > but did not get a chance ... > soon, > -m. > > > > On 06/16/2016 07:01 AM, robb wrote: > > motion sensor lights would be nice > > On Thu, Jun 16, 2016 at 4:51 AM, emaundu <emaundu(a)kijanigrows.com> > wrote: > >> hey bobby (hope i got that correct - ehh short term memory loss) >> hope well. >> nice meeting you earlier on ... >> what other data points do you think would be nice to collect and >> visualize >> in the sudoroom. >> thanks, >> -maundu >> >> >

can you tell me what pin the temperature sensor is supposed to connect? It got pulled out at some point and was sitting in some random analog pins. the wires are in the order RED, BLACK, YELLOW wow we figured it out, it's very confusing though. the ethernet port is serving DHCP out, but it's using its internal wifi antenna to get on the "sudoroom" wifi. our subnet is 100.*.*.* but I saw the IP address in the json linked from your URL below. does it contain a program to upload to its internal arduino? where's the program that's in the arduino now? thank you for this cool thing. we want to get it working to log the temperature in sudoroom, and maybe even to control a heater! -jake On Wed, 30 Nov 2016, emaundu wrote: > it is active ... > > http://api.kijanigrows.com/app > > and here > > http://api.kijanigrows.com/v2/devices/list > > and here > > http://api.kijanigrows.com/v2/maps/list > > > > On 11/30/2016 10:23 PM, Jake wrote: >> hi Eric, >> >> we have the controller powered up and plugged into internet, but it >> does not >> seem to be updating the page here: >> http://api.kijanigrows.com:3000/dashboard/db/sudoroom >> >> or here >> >> http://api.kijanigrows.com/app/#/device_sensors/sudoroom/ >> >> it definitely is plugged into ethernet and has a link and it is >> powered on. >> >> can we check on it somehow? how does it work? >> >> it's on the sudoroom hacking table right now, plugged in. i'm not >> sure if the >> sensors are connected right or not. >> >> thank you! >> -jake >> >> On Wed, 30 Nov 2016, robb wrote: >> >>> ---------- Forwarded message ---------- >>> From: emaundu <emaundu(a)kijanigrows.com> >>> Date: Thu, Jun 23, 2016 at 4:15 AM >>> Subject: Re: salaams >>> To: robb <sf99er(a)gmail.com> >>> >>> >>> hey robb. >>> hope well. >>> please could you reset the controller for me .... i think when i >>> left it >>> was not work .. >>> please could you reset the power switch (big white button on >>> bottom)... if >>> it works it should show data when you select say a last 15min data >>> setting >>> in the graphs below >>> the power switch maybe sticky/stiff due to the new cardboard i >>> swapped just >>> before i left. remove it from the wall where i taped it if need be to >>> ensure the button depresses off then on. >>> http://api.kijanigrows.com/app#/trends/sudoroom >>> or by seeing it's uptime update in this listing >>> http://api.kijanigrows.com/v2/devices/list >>> >>> thanks so very much in advance .. i planned on dropping by >>> yesterday/today >>> but did not get a chance ... >>> soon, >>> -m. >>> >>> >>> >>> On 06/16/2016 07:01 AM, robb wrote: >>> >>> motion sensor lights would be nice >>> >>> On Thu, Jun 16, 2016 at 4:51 AM, emaundu <emaundu(a)kijanigrows.com> >>> wrote: >>> >>>> hey bobby (hope i got that correct - ehh short term memory loss) >>>> hope well. >>>> nice meeting you earlier on ... >>>> what other data points do you think would be nice to collect and >>>> visualize >>>> in the sudoroom. >>>> thanks, >>>> -maundu >>>> >>>> >>> >

can you tell me what pin the temperature sensor is supposed to connect? It got pulled out at some point and was sitting in some random analog pins. the wires are in the order RED, BLACK, YELLOW wow we figured it out, it's very confusing though. the ethernet port is serving DHCP out, but it's using its internal wifi antenna to get on the "sudoroom" wifi. our subnet is 100.*.*.* but I saw the IP address in the json linked from your URL below. does it contain a program to upload to its internal arduino? where's the program that's in the arduino now? thank you for this cool thing. we want to get it working to log the temperature in sudoroom, and maybe even to control a heater! -jake On Wed, 30 Nov 2016, emaundu wrote: > it is active ... > > http://api.kijanigrows.com/app > > and here > > http://api.kijanigrows.com/v2/devices/list > > and here > > http://api.kijanigrows.com/v2/maps/list > > > > On 11/30/2016 10:23 PM, Jake wrote: >> hi Eric, >> >> we have the controller powered up and plugged into internet, but it >> does not >> seem to be updating the page here: >> http://api.kijanigrows.com:3000/dashboard/db/sudoroom >> >> or here >> >> http://api.kijanigrows.com/app/#/device_sensors/sudoroom/ >> >> it definitely is plugged into ethernet and has a link and it is >> powered on. >> >> can we check on it somehow? how does it work? >> >> it's on the sudoroom hacking table right now, plugged in. i'm not >> sure if the >> sensors are connected right or not. >> >> thank you! >> -jake >> >> On Wed, 30 Nov 2016, robb wrote: >> >>> ---------- Forwarded message ---------- >>> From: emaundu <emaundu(a)kijanigrows.com> >>> Date: Thu, Jun 23, 2016 at 4:15 AM >>> Subject: Re: salaams >>> To: robb <sf99er(a)gmail.com> >>> >>> >>> hey robb. >>> hope well. >>> please could you reset the controller for me .... i think when i >>> left it >>> was not work .. >>> please could you reset the power switch (big white button on >>> bottom)... if >>> it works it should show data when you select say a last 15min data >>> setting >>> in the graphs below >>> the power switch maybe sticky/stiff due to the new cardboard i >>> swapped just >>> before i left. remove it from the wall where i taped it if need be to >>> ensure the button depresses off then on. >>> http://api.kijanigrows.com/app#/trends/sudoroom >>> or by seeing it's uptime update in this listing >>> http://api.kijanigrows.com/v2/devices/list >>> >>> thanks so very much in advance .. i planned on dropping by >>> yesterday/today >>> but did not get a chance ... >>> soon, >>> -m. >>> >>> >>> >>> On 06/16/2016 07:01 AM, robb wrote: >>> >>> motion sensor lights would be nice >>> >>> On Thu, Jun 16, 2016 at 4:51 AM, emaundu <emaundu(a)kijanigrows.com> >>> wrote: >>> >>>> hey bobby (hope i got that correct - ehh short term memory loss) >>>> hope well. >>>> nice meeting you earlier on ... >>>> what other data points do you think would be nice to collect and >>>> visualize >>>> in the sudoroom. >>>> thanks, >>>> -maundu >>>> >>>> >>> >

ok i figured out the 1wire temperature sensor thing and i plugged it into pin 26 where it's supposed to go, and then i plugged it in, and then i reset the arduino side of the board, and now it seems to be working according to tail -f /tmp/serial.txt but the graph on the webpage is not updating. do i have to reboot the whole thing? http://api.kijanigrows.com:3000/dashboard/db/sudoroom?from=now-5m&to=now On Wed, 30 Nov 2016, emaundu wrote: > connectin 1-wire sensors > > http://kijanigrows.com/kb/using-1-wire-temperature-sensors-with-the-v2-cont… > > > it's a one wire ... vcc, gnd, and D6 ... see tutorial above > > > you configure wifi using ethernet .. just like you would your wifi > router at home. > > it is configured as a wifi client > > > connecting using wifi ip > > once you connect to wifi .. you don't need the cable you can connect > to the device using its wifi ip ... as found on json > > ssh root(a)192.168.195.176 (or 192.168.73.1 using ethernet) > > http://192.168.195.176 > > > connecting to wifi > > http://kijanigrows.com/kb/v2_board-how-to-connect-to-a-new-wifi-network/ > > > arduino and other files > > http://kijanigrows.com/support/download-libraries/ > > > On 11/30/2016 11:48 PM, Jake wrote: >> can you tell me what pin the temperature sensor is supposed to >> connect? It got >> pulled out at some point and was sitting in some random analog >> pins. the wires >> are in the order RED, BLACK, YELLOW >> >> wow we figured it out, it's very confusing though. the ethernet >> port is >> serving DHCP out, but it's using its internal wifi antenna to get on >> the >> "sudoroom" wifi. >> >> our subnet is 100.*.*.* but I saw the IP address in the json linked >> from your >> URL below. >> >> does it contain a program to upload to its internal arduino? where's >> the >> program that's in the arduino now? >> >> thank you for this cool thing. we want to get it working to log the >> temperature in sudoroom, and maybe even to control a heater! >> >> -jake >> >> On Wed, 30 Nov 2016, emaundu wrote: >> >>> it is active ... >>> >>> http://api.kijanigrows.com/app >>> >>> and here >>> >>> http://api.kijanigrows.com/v2/devices/list >>> >>> and here >>> >>> http://api.kijanigrows.com/v2/maps/list >>> >>> >>> >>> On 11/30/2016 10:23 PM, Jake wrote: >>>> hi Eric, >>>> >>>> we have the controller powered up and plugged into internet, but >>>> it does not >>>> seem to be updating the page here: >>>> http://api.kijanigrows.com:3000/dashboard/db/sudoroom >>>> >>>> or here >>>> >>>> http://api.kijanigrows.com/app/#/device_sensors/sudoroom/ >>>> >>>> it definitely is plugged into ethernet and has a link and it is >>>> powered on. >>>> >>>> can we check on it somehow? how does it work? >>>> >>>> it's on the sudoroom hacking table right now, plugged in. i'm not >>>> sure if the >>>> sensors are connected right or not. >>>> >>>> thank you! >>>> -jake >>>> >>>> On Wed, 30 Nov 2016, robb wrote: >>>> >>>>> ---------- Forwarded message ---------- >>>>> From: emaundu <emaundu(a)kijanigrows.com> >>>>> Date: Thu, Jun 23, 2016 at 4:15 AM >>>>> Subject: Re: salaams >>>>> To: robb <sf99er(a)gmail.com> >>>>> >>>>> >>>>> hey robb. >>>>> hope well. >>>>> please could you reset the controller for me .... i think when i >>>>> left it >>>>> was not work .. >>>>> please could you reset the power switch (big white button on >>>>> bottom)... if >>>>> it works it should show data when you select say a last 15min >>>>> data setting >>>>> in the graphs below >>>>> the power switch maybe sticky/stiff due to the new cardboard i >>>>> swapped just >>>>> before i left. remove it from the wall where i taped it if need >>>>> be to >>>>> ensure the button depresses off then on. >>>>> http://api.kijanigrows.com/app#/trends/sudoroom >>>>> or by seeing it's uptime update in this listing >>>>> http://api.kijanigrows.com/v2/devices/list >>>>> >>>>> thanks so very much in advance .. i planned on dropping by >>>>> yesterday/today >>>>> but did not get a chance ... >>>>> soon, >>>>> -m. >>>>> >>>>> >>>>> >>>>> On 06/16/2016 07:01 AM, robb wrote: >>>>> >>>>> motion sensor lights would be nice >>>>> >>>>> On Thu, Jun 16, 2016 at 4:51 AM, emaundu >>>>> <emaundu(a)kijanigrows.com> wrote: >>>>> >>>>>> hey bobby (hope i got that correct - ehh short term memory loss) >>>>>> hope well. >>>>>> nice meeting you earlier on ... >>>>>> what other data points do you think would be nice to collect and >>>>>> visualize >>>>>> in the sudoroom. >>>>>> thanks, >>>>>> -maundu >>>>>> >>>>>> >>>>> >>> >