sudo-discuss

sudo-discuss@sudoroom.org

6 participants
7410 discussions

by refugia

The interview is fun. There's a new party in spain with a participatory framework. Their sounds different than liquid democracy. http://www.shareable.net/blog/the-anti-party-spains-x-party-picks-up-steam

11 years, 4 months

Bay Area Digital Fabrication Club

by Vicky Knox

Y'all know about this? I just saw it on /r/Oakland. ;] http://www.meetup.com/Bay-Area-Digital-Fabrication-Club/

11 years, 4 months

OMNI Hackathon today - tomorrow (Sat/Sun)

by Matthew Senate

See the Agenda here: http://wiki.omni-oakland.org/w/Event:2014/05/03_Omni_Hackathon I'm bringing Sudo Mate, bananas, and apples for breakfast. I plan to brew coffee in the percolator at 2141 broadway. I'm also bringing two pastas, beet greens, and roasted beets for the pot luck lunch. Can anyone bring some carbonated water for the sudo mate? Extra sticky pads and markers (dry-erase AND permanent) would be invaluable! // Matt p.s. here's a static copy of the agenda as of the time I sent this email: Saturday - *10am*: Begin, light breakfast and coffee, start to add topics/projects to wall. - *11am*: Commencement Ceremony, Announcements, Agenda-setting - *12:30pm*: Pot-luck Lunch - *1pm - 5pm*: Break-out Sessions - Sessions should last around 30 min - 1 hour, have a note-taker (posting to wiki), and one person to plan to report back at the end of the day. - *5:30pm - 6:30pm*: Report-Back Sunday - *10am*: Begin again, light breakfast and coffee, start to revisit topics/projects on wall, notes on wiki, etc. - *11am - 12:30pm*: Break-out Sessions - *12:30pm*: Pot-luck Lunch - *1pm - 4pm*: Break-out Sessions - 3pm: Hacker Spa Mtg @ Arbor Cafe - *4:30pm - 5:30pm*: Report-Back

11 years, 4 months

Hackathon Agenda

by niki

Here's a breakdown of the discussions we will be having today. SESSIONS - money & outreach track - 1:30. Public Relations / Outreach / Interfacing with the Community & Gov - David - 2:30. Finances / Business Model / Income - Patrik +1 - 3:30. Fund-Raising Workshop - Danny +1 - - values track - 1:30. Safe space / Dominant Culture - Sarah - 2:30. Values - Jordan - 3:30. Bylaws - Ahnon - - logistics & governance track - 1:30. Membership / Access / Public- Andrew +1 - 2:30. Internal communications / working groups / process - Matt - 3:30. Using the common space / events - CONCLUSION - 4:30 - 5:15 -- ad-hoc session 4 - 5:45 - 6:30 -- report back

11 years, 4 months

NYC to convert phone booths into free WiFi and info kiosks

by Vicky Knox

The details are in the writing... http://america.aljazeera.com/articles/2014/5/2/new-york-city-callsforcitywi…

11 years, 4 months

omni.

by David Keenan

Hello everyone, If you are interested about what's up with Omni, I suggest you come to the hackathon tomorrow, as Matt said: http://wiki.omni-oakland.org/w/Event:2014/05/03_Omni_Hackathon INFOS WILL BE LIBERATED PROMPTLY AT 11AM ON THE DOT. "Doors" open at 10am with breakfast and coffee. Contact Matt Senate if you wanna help setup. Highly suggest Bring coffee (coffee grounds are best, one of the big containers), donuts, bagels, etc. We got our work cut out for us.. Suggest those with inquiring minds attend. Please? Because we need you. Now. So much love! David

11 years, 4 months

Re: [sudo-discuss] Any news about the Omni?

by Somebody

Be there before and or after the Rally+March at the Lake. Thanks! Yar <yardenack(a)gmail.com> wrote: >On Fri, May 2, 2014 at 4:09 PM, Somebody <somebody(a)riseup.net> wrote: >> Just "curioso". > >A lot of conversations are still happening. We're going to have even >more conversations at tomorrow's hackathon. Look forward to seeing you >there. :) >_______________________________________________ >sudo-discuss mailing list >sudo-discuss(a)lists.sudoroom.org >https://lists.sudoroom.org/listinfo/sudo-discuss

11 years, 4 months

Re: [sudo-discuss] Any news about the Omni?

by Yar

On Fri, May 2, 2014 at 4:09 PM, Somebody <somebody(a)riseup.net> wrote: > Just "curioso". A lot of conversations are still happening. We're going to have even more conversations at tomorrow's hackathon. Look forward to seeing you there. :)

11 years, 4 months

Any news about the Omni?

by Somebody

Just "curioso". Hol Gaskill <hol(a)gaskill.com> wrote: >i have to disagree on that assessment - if it's under closed loop control, it should be shut off once it reaches a certain temperature well below failure temp. if the thermistor reading is lagged significantly behind the temperature of the heating element then it will ramp up past the high temp each cycle for a period of time even with the thermistor functioning perfectly. not sure on conductivity of jb weld but i'd bet a 6 that pack thermal grease (either 'arctic cool' type or lithium grease) will solve the problem. > >on May 01, 2014, Jake <jake(a)spaz.org> wrote: >>once the resistor gets hotter than it should, it probably burns away >whatever paste is conducting its heat to the block, and runs away, so of >course there is no thermal glue there now..>>I believe putting a cyindrical resistor in a cylindrical hole in an >aluminum block is a recipe for disaster, unless you have magic thermal >glue that is also pliable, since everything is expanding and contracting >with every thermal cycle.>>I don't have any reason to believe there's anything wrong with the >thermistor, which is the temperature sensor.>>i'll probably be there on saturday. Do you know if JB weld is a good >choice for gluing the resistor in place?>>-jake>>On Thu, 1 May 2014, Hol Gaskill wrote:>>> just popped by the space and noticed the air gap - should probably use >> some kind of high temp thermal grease. my bet is that the heater was >> getting significantly above max temp but that heat wasn't getting >> conducted into the block and into the thermistor. i'll check mine and >> bri > ng in on saturday for omni hackathon with a side of 3ding - will you >> be around? would also like to learn how to work with thermistors.>>>> cheers>>>> on May 01, 2014, Jake <jake(a)spaz.org> wrote:>>> if the TAZ we has now has the 2.0 schnozzle then it might use the 4.7 ohm >resistor>as seen here:>http://www.lulzbot.com/products/heat-resistor-47-ohm>>of course the printer will work with a different resistor as long as it >provides>enough heat to print. Worst case we have to insert M220 S50 to >slow it down to half>speed printing until we get a better resistor...>>what value resistors do you have?>any special glue?>>On Thu, 1 May 2014, Hol Gaskill wrote:>>> this is what i pull>up for the part - 6.8 ohm:>> http://www.lulzbot.com/products/heat-resistor-68-ohm>>>> sounds like the most common reason for these failing is over temp from miscalibrated>thermistor>- i did find those 3 i got for the type a machine and if it's the same>part i'll>bring them in.>>>> on May 01, 2014, Jake <jake@sp > az.org> wrote:>>> so i spent all evening (and some of last night) to finally spool up the>>gigantic>pile of black filament for the TAZ 3D printer.>>i finally got it hung from>the wall>with a!> dust cover over it and ready to >feed smoothly into the printer, and then>i discovered>that the heating >element in its extruder head is dead.>>oh well.>>so,>we need a>new resistor to go in there. I don't know what the original >spec is, but>since the>whole thing runs on 24VDC and assuming 24 watts of >heat, that would be>a 24 ohm>resistor or so.>>Is someone other than me interested in contacting Lulzbot>and asking>>whether they want to send us a new resistor, or if they can tell us what>>part number>of resistor we should get as a replacement?>>-jake>>P.S. yes i tested>the resistor>and it's dead, infinite ohms, it's burned >out. When we get a replacement>we can>glue it in there better than they >apparently did. If the glue goes bad it>dies.>>>>>> >_______________________________________________ >sudo-discuss mailing list >sudo-discuss(a)lists.sudoroom.org >https://lists.sudoroom.org/listinfo/sudo-discuss

11 years, 4 months

# WEAPONIZED ARCHITECTURE /// Gentrifying Fortresses: A Case Study | The Funambulist

by Romy Snowyla

http://thefunambulist.net/2014/05/01/weaponized-architecture-gentrifying-fo… Sent from my iPhone

11 years, 4 months

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

sudo-discuss