7 Feb
2018
7 Feb
'18
3:18 p.m.
I mean if I cut the strip and use the power supply that is provided then I
need to come up with another power supply for the remainder of the tape
that I want to use later. So wondering if it’s easy to solder the wires
from another power supply onto the section that has been cut off?
On Wed, Feb 7, 2018 at 3:09 PM, Jake <jake(a)spaz.org> wrote:
i don't understand the question. There are solder
points at both ends of
each
discrete 3-LED circuit. You can splice this tape back together after
cutting
it if you solder carefully.
if you want to use multiple power supplies, they should be connected to
separate sections of LED tape, power supplies' outputs should not be
paralleled
together.
-jake
On Wed, 7 Feb 2018, Cere Davis wrote:
Is it relatively easy to splice in new power supplies into these things
--
*Cere Davis*
Science-Art | Kinetic Sculpture
CereDavis.com
@ceremona <http://Twitter.com/Ceremona>
after you’ve cut one?
On Wed, Feb 7, 2018 at 2:21 PM, Cere Davis <ceremona(a)gmail.com> wrote:
Thanks Jake.
On Wed, Feb 7, 2018 at 12:35 PM, Jake <jake(a)spaz.org> wrote:
hi Cere,
--
*Cere Davis*
Science-Art | Kinetic Sculpture
CereDavis.com
@ceremona <http://Twitter.com/Ceremona>
you're correct that you can cut that type of LED tape along any of the
dotted
lines. It's made up of a bunch of independant circuits which each have
3
LEDs
and resistors and run on 12V, and then they're all in parallel for 12V
down the
whole strip. The current draw from your 12V power supply will change
with the
number of LEDs, but the voltage will always be 12V.
-jake
On Wed, 7 Feb 2018, Cere Davis wrote:
Hey Folks,
>
> I’m sort of an LED nube and am looking for confirmation that this:
> https://www.aliexpress.com/item/5M-Roll-3528-60led-m-12VDC-I
> P65-soft-strip-light-5cm-cut-led-tape-light-for/32440112867.
> html?spm=2114.search0104.3.81.29a1356aJIB9xN&ws_ab_test=sear
> chweb0_0,searchweb201602_1_10152_10151_10065_10344_10130_100
> 68_10324_10547_10342_10325_10546_10343_10340_10548_10341_105
> 45_10084_10083_10618_10307_10313_10059_5722311_10534_100031_
> 10103_10624_10623_10622_10621_10620_10142,searchweb201603_
> 25,ppcSwitch_5&algo_expid=21979fdd-56eb-4fec-95af-89ed7a
> 33c672-12&algo_pvid=21979fdd-56eb-4fec-95af-89ed7a33c672&
> transAbTest=ae803_5&priceBeautifyAB=0
>
> <https://www.aliexpress.com/item/5M-Roll-3528-60led-m-12VDC-
> IP65-soft-strip-light-5cm-cut-led-tape-light-for/32440112867
> .html?spm=2114.search0104.3.81.29a1356aJIB9xN&ws_ab_test=sea
> rchweb0_0,searchweb201602_1_10152_10151_10065_10344_10130_10
> 068_10324_10547_10342_10325_10546_10343_10340_10548_10341_10
> 545_10084_10083_10618_10307_10313_10059_5722311_10534_100031
> _10103_10624_10623_10622_10621_10620_10142,searchweb201
> 603_25,ppcSwitch_5&algo_expid=21979fdd-56eb-4fec-95af-89ed7a
> 33c672-12&algo_pvid=21979fdd-56eb-4fec-95af-89ed7a33c672&
> transAbTest=ae803_5&priceBeautifyAB=0>item
> works they way I think it does. My only question, really, is whether I
> can
> just cut the strip at the designated locations and it will work fine
> with a
> 12v power supply without any need for extra resistors? It looks like
> the
> LEDs all sit in parallel along the strip so therefore…?
>
> Thanks,
> Cere
>
> --
> *Cere Davis*
>
> Science-Art | Kinetic Sculpture
> CereDavis.com
> @ceremona <http://Twitter.com/Ceremona>
>
>
--
*Cere Davis*
Science-Art | Kinetic Sculpture
CereDavis.com
@ceremona <http://Twitter.com/Ceremona>