20 Sep
2016
20 Sep
'16
8:13 a.m.
Does anyone know a good way to salvage from 101-105 mx brown keyboard
switches?
I'm planning on building my own keyboard this fall or winter and have
plenty of time to source scrap.
http://cubiq.org/build-your-very-own-pc-keyboard
Build process is as complex as you'd expect.
Teensy firmware: https://github.com/tmk/tmk_keyboard
Trent
20 Sep
20 Sep
10:14 a.m.
New subject: OK to borrow 3d printer for a few days?
Working on an LED baby toy for my daughter, getting a bit more
complicated than I thought and not easy to go back and forth between
sudo and home. Anyone have imminent prints to do on the TAZ? Would
bring back this weekend at the latest.
21 Sep
21 Sep
8:42 a.m.
New subject: OK to borrow 3d printer for a few days?
make your daughter happy!
On Tue, Sep 20, 2016 at 10:14 AM, <hol(a)gaskill.com> wrote:
Working on an LED baby toy for my daughter, getting a
bit more complicated
than I thought and not easy to go back and forth between sudo and home.
Anyone have imminent prints to do on the TAZ? Would bring back this
weekend at the latest.
_______________________________________________
sudo-discuss mailing list
sudo-discuss(a)lists.sudoroom.org
https://sudoroom.org/lists/listinfo/sudo-discuss
10:07 a.m.
New subject: OK to borrow 3d printer for a few days?
Trying here - noticed after I set it up at home that bead does not heat.
No voltage on the terminals inside the controller either, is there a
setting that can be changed via USB but not via the lcd screen menu? I
always just print from SD, noticed the temperature settings were off to
vs. last time I used it so will try this route. Nozzle is heating up
just fine so assuming power is nominal and it's a software issue.
On 2016-09-21 08:42, robb wrote:
make your daughter happy!
On Tue, Sep 20, 2016 at 10:14 AM, <hol(a)gaskill.com> wrote:
> Working on an LED baby toy for my daughter, getting a bit more complicated than I
thought and not easy to go back and forth between sudo and home. Anyone have imminent
prints to do on the TAZ? Would bring back this weekend at the latest.
> _______________________________________________
> sudo-discuss mailing list
> sudo-discuss(a)lists.sudoroom.org
> https://sudoroom.org/lists/listinfo/sudo-discuss [1]
Links:
------
[1] https://sudoroom.org/lists/listinfo/sudo-discuss
12:33 p.m.
New subject: OK to borrow 3d printer for a few days?
On Wed, Sep 21, 2016 at 1:07 PM, <hol(a)gaskill.com> wrote:
Trying here - noticed after I set it up at home that
bead does not heat. No
voltage on the terminals inside the controller either, is there a setting
that can be changed via USB but not via the lcd screen menu? I always just
print from SD, noticed the temperature settings were off to vs. last time I
used it so will try this route. Nozzle is heating up just fine so assuming
power is nominal and it's a software issue.
Bed heat is controlled by gcode. Make sure your slicer is set for it.
1:34 p.m.
New subject: OK to borrow 3d printer for a few days?
It is, have been using a modified version of mfgr's ABS print settings
in slic3r as always and it shows up as the target temp on the lcd screen
of the printer, just no voltage at the terminal for the heating element.
Installing latest version of Cura now to rule out gcode issues.
On 2016-09-21 12:33, Yardena Cohen wrote:
On Wed, Sep 21, 2016 at 1:07 PM,
<hol(a)gaskill.com> wrote:
Trying here - noticed after I set it up at home
that bead does not
heat. No
voltage on the terminals inside the controller either, is there a
setting
that can be changed via USB but not via the lcd screen menu? I always
just
print from SD, noticed the temperature settings were off to vs. last
time I
used it so will try this route. Nozzle is heating up just fine so
assuming
power is nominal and it's a software issue.
Bed heat is controlled by gcode. Make sure your slicer is set for it. 
22 Sep
22 Sep
3:25 p.m.
a hotplate covered with clean sand heated up to 400 degrees (celsius) will
be a surface on which you can place a circuitboard covered with such
switches, and then you can pluck them out of the board as their solder
melts. This is how old boards had their parts salvaged from them back
when people still did that.
if you don't have the right hotplate and you want to use a skillet
instead, you'll likely have to cut the circuitboard in half or thirds so
that it will be small enough to fit in the skillet of sand. no big deal.
you could also remove them one at a time, using a desoldering tool.
There's a motorized one at sudoroom, which is basically a gun-shaped
soldering iron with a hollow tip and a foot-pedal activated vacuum pump.
You could use that to pull the solder out of the hole for one of the two
pins of each key, and then use a regular soldering iron to heat up the
second one while pulling the key out with the other hand.
good luck,
-jake
On Tue, 20 Sep 2016, Trent Robbins wrote:
Does anyone know a good way to salvage from 101-105 mx
brown keyboard
switches?
I'm planning on building my own keyboard this fall or winter and have
plenty of time to source scrap.
http://cubiq.org/build-your-very-own-pc-keyboard
Build process is as complex as you'd expect.
Teensy firmware: https://github.com/tmk/tmk_keyboard
Trent
3:39 p.m.
Thanks Jake! I was planning on doing it by hand, but it would be neat to
try the mechanical one at sudo room.
Trent
On Thursday, September 22, 2016, Jake <jake(a)spaz.org> wrote:
a hotplate covered with clean sand heated up to 400
degrees (celsius) will
be a surface on which you can place a circuitboard covered with such
switches, and then you can pluck them out of the board as their solder
melts. This is how old boards had their parts salvaged from them back when
people still did that.
if you don't have the right hotplate and you want to use a skillet
instead, you'll likely have to cut the circuitboard in half or thirds so
that it will be small enough to fit in the skillet of sand. no big deal.
you could also remove them one at a time, using a desoldering tool.
There's a motorized one at sudoroom, which is basically a gun-shaped
soldering iron with a hollow tip and a foot-pedal activated vacuum pump.
You could use that to pull the solder out of the hole for one of the two
pins of each key, and then use a regular soldering iron to heat up the
second one while pulling the key out with the other hand.
good luck,
-jake
On Tue, 20 Sep 2016, Trent Robbins wrote:
Does anyone know a good way to salvage from 101-105 mx brown keyboard
> switches?
>
> I'm planning on building my own keyboard this fall or winter and have
> plenty of time to source scrap.
>
> http://cubiq.org/build-your-very-own-pc-keyboard
>
> Build process is as complex as you'd expect.
>
> Teensy firmware: https://github.com/tmk/tmk_keyboard
>
>
>
> Trent
>
>
--
(Sent from cellphone)
2795
days inactive
2797
days old
7 comments
5 participants
participants (5)
-
hol＠gaskill.com -
Jake -
robb -
Trent Robbins -
Yardena Cohen