29 Oct
2013
29 Oct
'13
6:21 p.m.
Hi,
Who's the current guru on running the 3D printer? Is it possible to get
together and learn how to work it? Are there any 3D printing events or
classes planned?
--
-steve
30 Oct
30 Oct
11:11 a.m.
Hey Steve,
I've used it somewhat recently although I've since seen what looks like some very
minor damage to the build platform from improper use. I never learned how to override the
zeroing on the Z axis but I'm game to hack on it for a bit. Best time for a quick
test would be around noon weekdays - do you have a specific part in mind? I'm going
to send some models to shapeways soon so I wouldn't mind getting our printer tuned up
for a rough draft.
Cheers,
Hol
Oct 29, 2013 06:21:14 PM, steveberl(a)gmail.com wrote:
Hi,
Who's the current guru on running the 3D printer?
Is it possible to get together and learn how to work it? Are there any 3D printing events
or classes planned?
--
-steve
_______________________________________________
sudo-discuss mailing list
sudo-discuss(a)lists.sudoroom.org
http://lists.sudoroom.org/listinfo/sudo-discuss
11:21 a.m.
The secret incantation for zeroing is "G92 Z0". when sent from pronterface
this saves the current z position as the 0 point. so once you have it at
the right height using the 0.1mm up/down buttons, just send the magic
words. if the correct position is lower than the current 0 point, you may
will first have to do "G92 Z10" in order to let it move lower.
Once you get it dialed in, i think it needs to get written into eeprom to
avoid losing the setting after a power cycle. i'm not sure if there's a
command for that or whether you will need to reflash the controller.
On Wed, Oct 30, 2013 at 11:11 AM, Hol Gaskill <hol(a)gaskill.com> wrote:
Hey Steve,
I've used it somewhat recently although I've since seen what looks like
some very minor damage to the build platform from improper use. I never
learned how to override the zeroing on the Z axis but I'm game to hack on
it for a bit. Best time for a quick test would be around noon weekdays -
do you have a specific part in mind? I'm going to send some models to
shapeways soon so I wouldn't mind getting our printer tuned up for a rough
draft.
Cheers,
Hol
Oct 29, 2013 06:21:14 PM, steveberl(a)gmail.com wrote:
Hi,
>_______________________________________________
>sudo-discuss mailing list
>sudo-discuss(a)lists.sudoroom.org
>http://lists.sudoroom.org/listinfo/sudo-discuss
_______________________________________________
sudo-discuss mailing list
sudo-discuss(a)lists.sudoroom.org
http://lists.sudoroom.org/listinfo/sudo-discuss
Who's the current guru on running the 3D
printer? Is it possible to get
together and learn how to work it? Are there any 3D
printing events or
classes planned?
--
-steve
12:02 p.m.
I work for a 3d printing company about 6 blocks away from sudoroom...I
should come over there at some point and fix up the printer.
On Wed, Oct 30, 2013 at 11:21 AM, lilia <liliakai(a)gmail.com> wrote:
The secret incantation for zeroing is "G92
Z0". when sent from pronterface
this saves the current z position as the 0 point. so once you have it at
the right height using the 0.1mm up/down buttons, just send the magic
words. if the correct position is lower than the current 0 point, you may
will first have to do "G92 Z10" in order to let it move lower.
Once you get it dialed in, i think it needs to get written into eeprom to
avoid losing the setting after a power cycle. i'm not sure if there's a
command for that or whether you will need to reflash the controller.
On Wed, Oct 30, 2013 at 11:11 AM, Hol Gaskill <hol(a)gaskill.com> wrote:
Hey Steve,
I've used it somewhat recently although I've since seen what looks like
some very minor damage to the build platform from improper use. I never
learned how to override the zeroing on the Z axis but I'm game to hack on
it for a bit. Best time for a quick test would be around noon weekdays -
do you have a specific part in mind? I'm going to send some models to
shapeways soon so I wouldn't mind getting our printer tuned up for a rough
draft.
Cheers,
Hol
Oct 29, 2013 06:21:14 PM, steveberl(a)gmail.com wrote:
Hi,
>_______________________________________________
>sudo-discuss mailing list
>sudo-discuss(a)lists.sudoroom.org
>http://lists.sudoroom.org/listinfo/sudo-discuss
_______________________________________________
sudo-discuss mailing list
sudo-discuss(a)lists.sudoroom.org
http://lists.sudoroom.org/listinfo/sudo-discuss
_______________________________________________
sudo-discuss mailing list
sudo-discuss(a)lists.sudoroom.org
http://lists.sudoroom.org/listinfo/sudo-discuss
Who's the current guru on running the 3D
printer? Is it possible to get
together and learn how to work it? Are there any 3D
printing events or
classes planned?
--
-steve
1 p.m.
Yes Dave. That would be wonderful.
Steve
On Wednesday, October 30, 2013, Hol Gaskill wrote:
genius, thank you!
on Oct 30, 2013, *lilia* <liliakai(a)gmail.com <javascript:_e({}, 'cvml',
'liliakai(a)gmail.com');>> wrote:
The secret incantation for zeroing is "G92 Z0". when sent from pronterface
this saves the current z position as the 0 point. so once you have it at
the right height using the 0.1mm up/down buttons, just send the magic
words. if the correct position is lower than the current 0 point, you may
will first have to do "G92 Z10" in order to let it move lower.
Once you get it dialed in, i think it needs to get written into eeprom to
avoid losing the setting after a power cycle. i'm not sure if there's a
command for that or whether you will need to reflash the controller.
On Wed, Oct 30, 2013 at 11:11 AM, Hol Gaskill <hol@gaskill.com<javascript:_e({},
'cvml', 'hol(a)gaskill.com');>
--
-steve
wrote:
Hey Steve,
I've used it somewhat recently although I've since seen what looks like
some very minor damage to the build platform from improper use. I never
learned how to override the zeroing on the Z axis but I'm game to hack on
it for a bit. Best time for a quick test would be around noon weekdays -
do you have a specific part in mind? I'm going to send some models to
shapeways soon so I wouldn't mind getting our printer tuned up for a rough
draft.
Cheers,
Hol
Oct 29, 2013 06:21:14 PM, steveberl(a)gmail.com <javascript:_e({}, 'cvml',
'steveberl(a)gmail.com');> wrote:
Hi,
>_______________________________________________
>sudo-discuss mailing list
>sudo-discuss(a)lists.sudoroom.org <javascript:_e({}, 'cvml',
'sudo-discuss(a)lists.sudoroom.org');>
>http://lists.sudoroom.org/listinfo/sudo-discuss
_______________________________________________
sudo-discuss mailing list
sudo-discuss(a)lists.sudoroom.org <javascript:_e({}, 'cvml',
'sudo-discuss(a)lists.sudoroom.org');>
http://lists.sudoroom.org/listinfo/sudo-discuss
Who's the current guru on running the 3D
printer? Is it possible to get
together and learn how to work it? Are there any 3D
printing events or
classes planned?
--
-steve
4072
days inactive
4072
days old
5 comments
4 participants
participants (4)
-
David Rorex -
Hol Gaskill -
lilia -
Steve Berl