2 Oct
2018
2 Oct
'18
5:17 p.m.
Trying to get through a project but the laser isn't behaving. Stalls during
a cut (with laser on of course) but manages tp start back up a dozen times
before just stopping and burning a hole in the piece. Tried 4 or 5 usb
cables with varying results but still couldn't get a complete cut
2 Oct
2 Oct
5:24 p.m.
Of course I try "just one more cable" and it works. It shockingly lives
another day.
On Tue, Oct 2, 2018, 5:17 PM Morgan Allen <morganrallen(a)gmail.com> wrote:
Trying to get through a project but the laser
isn't behaving. Stalls
during a cut (with laser on of course) but manages tp start back up a dozen
times before just stopping and burning a hole in the piece. Tried 4 or 5
usb cables with varying results but still couldn't get a complete cut
5:31 p.m.
viva la laser cutter!
On Tue, Oct 2, 2018 at 5:25 PM Morgan Allen <morganrallen(a)gmail.com> wrote:
Of course I try "just one more cable" and it
works. It shockingly lives
another day.
On Tue, Oct 2, 2018, 5:17 PM Morgan Allen <morganrallen(a)gmail.com> wrote:
--
*First they ignore you, then they laugh at you, then they fight you, then
you win*.
- Mohandas Karamchand Gandhi
CONFIDENTIALITY NOTICE:
The contents of this email message and any attachments are intended solely
for the addressee(s) and may contain confidential and/or privileged
information and may be legally protected from disclosure. If you are not
the intended recipient of this message or their agent, or if this message
has been addressed to you in error, please immediately alert the sender by
reply email and then delete this message and any attachments. If you are
not the intended recipient, you are hereby notified that any use,
dissemination, copying, or storage of this message or its attachments is
strictly prohibited.
Trying to get through a project but the laser
isn't behaving. Stalls
during a cut (with laser on of course) but manages tp start back up a dozen
times before just stopping and burning a hole in the piece. Tried 4 or 5
usb cables with varying results but still couldn't get a complete cut
_______________________________________________
sudo-discuss mailing list
sudo-discuss(a)lists.sudoroom.org
https://sudoroom.org/lists/listinfo/sudo-discuss
5:52 p.m.
jeez do you think it was a bad USB cable or a coincidence of something else
going wrong? were you using your own computer or the dedicated desktop?
On Tue, 2 Oct 2018, Morgan Allen wrote:
Of course I try "just one more cable" and it
works. It shockingly lives
another day.
On Tue, Oct 2, 2018, 5:17 PM Morgan Allen <morganrallen(a)gmail.com> wrote:
Trying to get through a project but the laser
isn't behaving. Stalls
during a cut (with laser on of course) but manages tp start back up a dozen
times before just stopping and burning a hole in the piece. Tried 4 or 5
usb cables with varying results but still couldn't get a complete cut
3 Oct
3 Oct
11:59 a.m.
@robb eeeh, not quite.
@jake 4 bad USB cables then 1 mediocre one? Dunno, theories:
1)
USB Connector is worn and the cable needs to have good springyness to make
contact.
2)
The power supply in the cutter is dying and causing power sags,
the higher quality cable is more fault tolerant when this happens.
In the end, stalling still occurred with the best cable. Other problems
observed, despite various
focal lengths I had to cut <30% speed, 100% power 4-5 passes to cut 1/8"
acrylic.
In the past I would have cut this with round 40/60 3 passes. This could be
mirror focusing, which
I didn't have time to perform. I also noticed a burnt spot on mirror #2.
Between stalling and burnt mirrors I'm going to go out on a limb and say
this is unsafe to use
until a major overhaul is performed.
On Tue, Oct 2, 2018 at 5:52 PM Jake <jake(a)spaz.org> wrote:
jeez do you think it was a bad USB cable or a
coincidence of something else
going wrong? were you using your own computer or the dedicated desktop?
On Tue, 2 Oct 2018, Morgan Allen wrote:
Of course I try "just one more cable"
and it works. It shockingly lives
another day.
On Tue, Oct 2, 2018, 5:17 PM Morgan Allen <morganrallen(a)gmail.com>
wrote:
> Trying to get through a project but the laser isn't behaving. Stalls
> during a cut (with laser on of course) but manages tp start back up a
dozen
times
before just stopping and burning a hole in the piece. Tried 4 or 5
usb cables with varying results but still couldn't get a complete cut
2:10 p.m.
i wonder if it needz itz contacts cleaned
i'll spray the usb port w/contact cleaner 2day
On Wed, Oct 3, 2018 at 12:00 PM Morgan Allen <morganrallen(a)gmail.com> wrote:
@robb eeeh, not quite.
@jake 4 bad USB cables then 1 mediocre one? Dunno, theories:
1)
USB Connector is worn and the cable needs to have good springyness to make
contact.
2)
The power supply in the cutter is dying and causing power sags,
the higher quality cable is more fault tolerant when this happens.
In the end, stalling still occurred with the best cable. Other problems
observed, despite various
focal lengths I had to cut <30% speed, 100% power 4-5 passes to cut 1/8"
acrylic.
In the past I would have cut this with round 40/60 3 passes. This could be
mirror focusing, which
I didn't have time to perform. I also noticed a burnt spot on mirror #2.
Between stalling and burnt mirrors I'm going to go out on a limb and say
this is unsafe to use
until a major overhaul is performed.
On Tue, Oct 2, 2018 at 5:52 PM Jake <jake(a)spaz.org> wrote:
--
*First they ignore you, then they laugh at you, then they fight you, then
you win*.
- Mohandas Karamchand Gandhi
CONFIDENTIALITY NOTICE:
The contents of this email message and any attachments are intended solely
for the addressee(s) and may contain confidential and/or privileged
information and may be legally protected from disclosure. If you are not
the intended recipient of this message or their agent, or if this message
has been addressed to you in error, please immediately alert the sender by
reply email and then delete this message and any attachments. If you are
not the intended recipient, you are hereby notified that any use,
dissemination, copying, or storage of this message or its attachments is
strictly prohibited.
jeez do you think it was a bad USB cable or a
coincidence of something
else
going wrong? were you using your own computer or the dedicated desktop?
On Tue, 2 Oct 2018, Morgan Allen wrote:
_______________________________________________
sudo-discuss mailing list
sudo-discuss(a)lists.sudoroom.org
https://sudoroom.org/lists/listinfo/sudo-discuss
Of course I try "just one more cable"
and it works. It shockingly lives
another day.
On Tue, Oct 2, 2018, 5:17 PM Morgan Allen <morganrallen(a)gmail.com>
wrote:
> Trying to get through a project but the laser isn't behaving. Stalls
> during a cut (with laser on of course) but manages tp start back up a
dozen
> times before just stopping and burning a hole
in the piece. Tried 4 or
5
usb
cables with varying results but still couldn't get a complete cut
12 Oct
12 Oct
8:17 a.m.
Were you printing on vector or raster mode? Last time I used it there
was all kinds of crazy behavior until I switched over to vector mode,
cut like a charm. That's the one tool I keep meaning to swing by and
use but never leave enough time to get set up for.
On 2018-10-03 14:10, robb wrote:
i wonder if it needz itz contacts cleaned
i'll spray the usb port w/contact cleaner 2day
On Wed, Oct 3, 2018 at 12:00 PM Morgan Allen <morganrallen(a)gmail.com> wrote:
@robb eeeh, not quite.
@jake 4 bad USB cables then 1 mediocre one? Dunno, theories:
1)
USB Connector is worn and the cable needs to have good springyness to make contact.
2)
The power supply in the cutter is dying and causing power sags,
the higher quality cable is more fault tolerant when this happens.
In the end, stalling still occurred with the best cable. Other problems observed, despite
various
focal lengths I had to cut <30% speed, 100% power 4-5 passes to cut 1/8" acrylic.
In the past I would have cut this with round 40/60 3 passes. This could be mirror
focusing, which
I didn't have time to perform. I also noticed a burnt spot on mirror #2.
Between stalling and burnt mirrors I'm going to go out on a limb and say this is
unsafe to use
until a major overhaul is performed.
On Tue, Oct 2, 2018 at 5:52 PM Jake <jake(a)spaz.org> wrote: jeez do you think it was
a bad USB cable or a coincidence of something else
going wrong? were you using your own computer or the dedicated desktop?
On Tue, 2 Oct 2018, Morgan Allen wrote:
--
_FIRST THEY IGNORE YOU, THEN THEY LAUGH AT YOU, THEN THEY FIGHT YOU,
THEN YOU WIN_.
- Mohandas Karamchand Gandhi
CONFIDENTIALITY NOTICE:
The contents of this email message and any attachments are intended
solely for the addressee(s) and may contain confidential and/or
privileged information and may be legally protected from disclosure. If
you are not the intended recipient of this message or their agent, or if
this message has been addressed to you in error, please immediately
alert the sender by reply email and then delete this message and any
attachments. If you are not the intended recipient, you are hereby
notified that any use, dissemination, copying, or storage of this
message or its attachments is
strictly prohibited.
_______________________________________________
sudo-discuss mailing list
sudo-discuss(a)lists.sudoroom.org
https://sudoroom.org/lists/listinfo/sudo-discuss
Of course I try "just one more cable"
and it works. It shockingly lives
another day.
On Tue, Oct 2, 2018, 5:17 PM Morgan Allen <morganrallen(a)gmail.com> wrote:
sudo-discuss mailing list
sudo-discuss(a)lists.sudoroom.org
https://sudoroom.org/lists/listinfo/sudo-discuss Trying to get through a project but the laser
isn't behaving. Stalls
during a cut (with laser on of course) but manages tp start back up a dozen
times before just stopping and burning a hole in the piece. Tried 4 or 5
usb cables with varying results but still couldn't get a complete cut
_______________________________________________
10:49 a.m.
It was vector. The issue with raster mode is usually the end switch (on the
left side of the gantry) comes loose.
On Fri, Oct 12, 2018 at 8:17 AM <hol(a)gaskill.com> wrote:
Were you printing on vector or raster mode? Last time
I used it there was
all kinds of crazy behavior until I switched over to vector mode, cut like
a charm. That's the one tool I keep meaning to swing by and use but never
leave enough time to get set up for.
On 2018-10-03 14:10, robb wrote:
i wonder if it needz itz contacts cleaned
i'll spray the usb port w/contact cleaner 2day
On Wed, Oct 3, 2018 at 12:00 PM Morgan Allen <morganrallen(a)gmail.com>
wrote:
@robb eeeh, not quite.
@jake 4 bad USB cables then 1 mediocre one? Dunno, theories:
1)
USB Connector is worn and the cable needs to have good springyness to
make contact.
2)
The power supply in the cutter is dying and causing power sags,
the higher quality cable is more fault tolerant when this happens.
In the end, stalling still occurred with the best cable. Other problems
observed, despite various
focal lengths I had to cut <30% speed, 100% power 4-5 passes to cut 1/8"
acrylic.
In the past I would have cut this with round 40/60 3 passes. This could
be mirror focusing, which
I didn't have time to perform. I also noticed a burnt spot on mirror #2.
Between stalling and burnt mirrors I'm going to go out on a limb and say
this is unsafe to use
until a major overhaul is performed.
On Tue, Oct 2, 2018 at 5:52 PM Jake <jake(a)spaz.org> wrote:
--
*First they ignore you, then they laugh at you, then they fight you, then
you win*.
- Mohandas Karamchand Gandhi
CONFIDENTIALITY NOTICE:
The contents of this email message and any attachments are intended solely
for the addressee(s) and may contain confidential and/or privileged
information and may be legally protected from disclosure. If you are not
the intended recipient of this message or their agent, or if this message
has been addressed to you in error, please immediately alert the sender by
reply email and then delete this message and any attachments. If you are
not the intended recipient, you are hereby notified that any use,
dissemination, copying, or storage of this message or its attachments is
strictly prohibited.
_______________________________________________
sudo-discuss mailing list
sudo-discuss(a)lists.sudoroom.org
https://sudoroom.org/lists/listinfo/sudo-discuss
jeez do you think it was a bad USB cable or a
coincidence of something
else
going wrong? were you using your own computer or the dedicated desktop?
On Tue, 2 Oct 2018, Morgan Allen wrote:
_______________________________________________
sudo-discuss mailing list
sudo-discuss(a)lists.sudoroom.org
https://sudoroom.org/lists/listinfo/sudo-discuss Of course I try "just one more cable"
and it works. It shockingly lives
another day.
On Tue, Oct 2, 2018, 5:17 PM Morgan Allen <morganrallen(a)gmail.com>
wrote:
> Trying to get through a project but the laser isn't behaving. Stalls
> during a cut (with laser on of course) but manages tp start back up a
dozen
> times before just stopping and burning a hole
in the piece. Tried 4
or 5
>> usb cables with varying results but still couldn't get a complete cut
>>
>
2263
days inactive
2272
days old
7 comments
4 participants
participants (4)
-
hol＠gaskill.com -
Jake -
Morgan Allen -
robb