6 Jul
2014
6 Jul
'14
3:45 a.m.
I've been working on the door access system all night. Everything was
working fine, but now close works, but open does not, the motor just stops
half way. I'm sorry for the inconvenience, but I have to stop working on
this and come back tomorrow.
Until then I have disabled the mag swipe to prevent any damage to the
system.
Thanks,
Andrew
--
-------
Andrew Lowe
Cell: 831-332-2507
http://roshambomedia.com
6 Jul
6 Jul
5:01 p.m.
what kind of motor is it?
On 2014-07-06 03:45, Andrew wrote:
I've been working on the door access system all
night. Everything was working fine, but now close works, but open does not, the motor just
stops half way. I'm sorry for the inconvenience, but I have to stop working on this
and come back tomorrow.
Until then I have disabled the mag swipe to prevent any damage to the system.
Thanks, Andrew
--
-------
Andrew Lowe
Cell: 831-332-2507
http://roshambomedia.com [2]
_______________________________________________
sudo-discuss mailing list
sudo-discuss(a)lists.sudoroom.org
https://lists.sudoroom.org/listinfo/sudo-discuss [1]
Links:
------
[1] https://lists.sudoroom.org/listinfo/sudo-discuss
[2] http://roshambomedia.com
10:55 p.m.
Follow up: seems like there was a bit of tension on the lumber that spans
most of the height of the door, attached at the bottom to the motor (and
thus the bottom latch) and attached above to the top latch.
A small metal piece that acts as a guide to this piece of lumber was
especially tight, so we loosened the screws on it no more than a turn each,
which seems to have allowed a bit more give.
In conclusion, this may or may not have been the problem, and perhaps there
are other problems, but the mechanism seems to be working at the moment.
Unless, on the other hand, Andrew any more information to report.
// Matt
On Sun, Jul 6, 2014 at 5:01 PM, <hol(a)gaskill.com> wrote:
what kind of motor is it?
On 2014-07-06 03:45, Andrew wrote:
I've been working on the door access system all night. Everything was
working fine, but now close works, but open does not, the motor just stops
half way. I'm sorry for the inconvenience, but I have to stop working on
this and come back tomorrow.
Until then I have disabled the mag swipe to prevent any damage to the
system.
Thanks,
Andrew
--
-------
Andrew Lowe
Cell: 831-332-2507
http://roshambomedia.com
_______________________________________________
sudo-discuss mailing
listsudo-discuss@lists.sudoroom.orghttps://lists.sudoroom.org/listinfo/sudo-discuss
_______________________________________________
sudo-discuss mailing list
sudo-discuss(a)lists.sudoroom.org
https://lists.sudoroom.org/listinfo/sudo-discuss
11:27 p.m.
I will see your update and raise you another update. The issue came back
despite the loosening of the screws.
On Jul 6, 2014 10:55 PM, "Matthew Senate" <mattsenate(a)gmail.com> wrote:
Follow up: seems like there was a bit of tension on
the lumber that spans
most of the height of the door, attached at the bottom to the motor (and
thus the bottom latch) and attached above to the top latch.
A small metal piece that acts as a guide to this piece of lumber was
especially tight, so we loosened the screws on it no more than a turn each,
which seems to have allowed a bit more give.
In conclusion, this may or may not have been the problem, and perhaps
there are other problems, but the mechanism seems to be working at the
moment. Unless, on the other hand, Andrew any more information to report.
// Matt
On Sun, Jul 6, 2014 at 5:01 PM, <hol(a)gaskill.com> wrote:
what kind of motor is it?
On 2014-07-06 03:45, Andrew wrote:
I've been working on the door access system all night. Everything was
working fine, but now close works, but open does not, the motor just stops
half way. I'm sorry for the inconvenience, but I have to stop working on
this and come back tomorrow.
Until then I have disabled the mag swipe to prevent any damage to the
system.
Thanks,
Andrew
--
-------
Andrew Lowe
Cell: 831-332-2507
http://roshambomedia.com
_______________________________________________
sudo-discuss mailing
listsudo-discuss@lists.sudoroom.orghttps://lists.sudoroom.org/listinfo/sudo-discuss
_______________________________________________
sudo-discuss mailing list
sudo-discuss(a)lists.sudoroom.org
https://lists.sudoroom.org/listinfo/sudo-discuss
17 Jul
17 Jul
9:55 p.m.
what is the current status of the door?
On Sun, Jul 6, 2014 at 11:27 PM, Andrew <andrew(a)roshambomedia.com> wrote:
I will see your update and raise you another update.
The issue came back
despite the loosening of the screws.
On Jul 6, 2014 10:55 PM, "Matthew Senate" <mattsenate(a)gmail.com> wrote:
Follow up: seems like there was a bit of tension
on the lumber that spans
most of the height of the door, attached at the bottom to the motor (and
thus the bottom latch) and attached above to the top latch.
A small metal piece that acts as a guide to this piece of lumber was
especially tight, so we loosened the screws on it no more than a turn each,
which seems to have allowed a bit more give.
In conclusion, this may or may not have been the problem, and perhaps
there are other problems, but the mechanism seems to be working at the
moment. Unless, on the other hand, Andrew any more information to report.
// Matt
On Sun, Jul 6, 2014 at 5:01 PM, <hol(a)gaskill.com> wrote:
_______________________________________________
sudo-discuss mailing list
sudo-discuss(a)lists.sudoroom.org
https://lists.sudoroom.org/listinfo/sudo-discuss
what kind of motor is it?
On 2014-07-06 03:45, Andrew wrote:
I've been working on the door access system all night. Everything was
working fine, but now close works, but open does not, the motor just stops
half way. I'm sorry for the inconvenience, but I have to stop working on
this and come back tomorrow.
Until then I have disabled the mag swipe to prevent any damage to the
system.
Thanks,
Andrew
--
-------
Andrew Lowe
Cell: 831-332-2507
http://roshambomedia.com
_______________________________________________
sudo-discuss mailing
listsudo-discuss@lists.sudoroom.orghttps://lists.sudoroom.org/listinfo/sudo-discuss
_______________________________________________
sudo-discuss mailing list
sudo-discuss(a)lists.sudoroom.org
https://lists.sudoroom.org/listinfo/sudo-discuss
3810
days inactive
3822
days old
5 comments
5 participants
participants (5)
-
Andrew -
hol＠gaskill.com -
Marc Juul -
Marina Kukso -
Matthew Senate