sudo-discuss

sudo-discuss@sudoroom.org

8 participants
7470 discussions

by Jake

last night I replaced the hotend on the sudoroom type-a-machine 3d printer. after that i spent a bit of time attempting to print and kept running into problems, which i'll list. it seems that some of the PLA we have that came from type A machines is clearly labeled to be printed at 190-220 degrees! I have always used 185, but i guess this is a new formula. When i set it to 205 it still seemed too cold, so i ended up using 220. You should set the temperature in the slic3r before you export your gcode. There are other ways to do it, but if you know them you don't need me to tell you. the other issue is that our spools of filament are dusty! it's gross. And all that dust goes into the extruder and jams it up. The nozzle is only 0.35mm diameter! so clean the filament spool first (DO NOT GET PLA WET) and keep a dust-catcher on the filament before it goes into the machine. I put one on there last night. something like this would be fine, if we had the right foam, but for now i just cut some acrylic fabric and wrapped it around the filament with some copper wire to hold it on there. It should work but check it once in a while, or when changing spools. someone had put tape over the old tape on the platform in a very chaotic and haphazard way. Also there were a few melted spots on the platform where a hot extruder had been rammed into the platform and created a little vulcano. I carved the raised spots off the platform with a flat-edged blade, leveling them off, and then i re-arranged the tape properly so there is NO OVERLAPPING OF TAPE and only one layer of tape. It is necessary to maintain the platform any time you're trying to print if it is not already good to go. I didn't re-level the platform so if someone else wants to do that go ahead. It seemed a bit higher on the left than on the right. I like to get a perfectly cylindrical object and adjust the z-height so it just barely rolls under the extruder tip, and then try in four corners of the platform to compare the height. now join the sudo-prints mailing list! http://lists.sudoroom.org/listinfo/sudo-prints -jake

12 years, 3 months

sudoroom mailinglist just for printers!

by Jake

Sudoroom has so many printers, it's hard to keep track! 2D printers, 3D printers, label printers, and even screenprinters! there's some sort of weird flyer-duplicating machine that makes only green ink but is really cheap to use, there's that new fancy COLOR laser printer... so here is a new list, sudo-prints(a)lists.sudoroom.org if you know how to use one of the printers at sudoroom, including the CNC machine (hey it can print in wood) please subscribe to this list! then we can put labels on all the sudo printers that say "have questions about using this machine? noticed something you think others should know? do you know how to use it and want to help others? write to sudo-prints(a)lists.sudoroom.org !!!" your present for joining this list is that you get to hear about the sudoroom 3d printer, latest news, a post that i will write right now. -jake

12 years, 3 months

Re: [sudo-discuss] Sudouino328 PCB Design

by Jake

Hi Hol, I have lots of opinions and advice about this design, but i would like more info about the state of the project first. For example i am curious whether this thing will have a USB port or use the 6-pin serial header like a Boarduino. I have a bunch of Atmega32U4 chips that you can use for this project. True that they are surfacemount but it's not harder to do than through-hole, in fact it can be much easier even for newbies. I have syringes of solder paste, although it can be done with regular solder easily. here's a video of someone doing it with hot air (note: they fool around with the narrow stream of hot air, but you can just do it in a blast with a regular hotair gun in much less time) http://www.youtube.com/watch?feature=player_detailpage&v=2Z7nCAxS2Rg#t=548 the nice thing about the atmega32U4 chips (besides the fact that I will donate them to the project for free) is that they have native USB, which means your boards can plug straight into a computer like an arduino leonardo. Also they will be able to pretend to be other devices, like a keyboard, mouse, printer, disk, or whatever you want. specifically about the SAE connectors, I am against them. I think the board should just have 1/8" holes for wires to be soldered into. -jake Hol wrote: Almost done w/ PCB design. That's an ATMega328p processor and a ULN2003 for power output up to 3.5 amps out of the box. Still need to add some connectors for I2C and 12V, 5V. I usually use SAE connectors http://www.vetco.net/catalog/images/G-QD-10-2.jpg for my 12V loads but we could solder on a barrel jack, or just ship it with holes for DIY soldering of connectors. Suggestions?

12 years, 3 months

Fwd: hackerspace burn-out

by Chris Bee

---------- Forwarded message ---------- From: Chris Bee <hotelcompany(a)gmail.com> Date: Sun, Dec 22, 2013 at 12:03 AM Subject: Re: [sudo-discuss] hackerspace burn-out To: Romy Snowyla <romy(a)snowyla.com> I agree with everything on that list, and speaking for myself I think I deal with those issues well enough...I'm pretty good at compartmentalization, and can recognize when the issue lies within me and not assign blame or heat where it's neither needed nor warranted. But... I'd like to add "failure to grasp or acknowledge the DIY aspect of hackerspaces." This is directed towards people (NOT sudoers) who seem to regard sudo as a go-to for broken shit that they have no intention of fixing themselves...I don't mind helping people as long as a) they want to be involved with the process of getting their gear working again and b) don't expect me to put whatever I'm doing at the moment on hold to give them my undivided attention. This has probably happened to all of us at one point or another...I'm getting better at setting boundaries but sometimes I feel like I have to be short with people who I really don't want to alienate but who simply aren't going to get the message any other way. One thing I've started doing is wearing a large pair of headphones, which is a cue I picked up from juul....if that doesn't send a clear signal that "I'm here temporally but somewhere else psychically" then I figure it's okay for me to let whoever is trying to drag me into their project what's really going on. -chrisbee On Tue, Dec 17, 2013 at 5:30 PM, Romy Snowyla <romy(a)snowyla.com> wrote: > Unrealistic expectations > One bad evening improperly distorting perception of hackerspace as a whole > Lack of sleep > Unrealistic understanding of basic human social dynamics > Personal conflicts > > > Sent from my iPhone > > On Dec 17, 2013, at 2:23 PM, Craig Rouskey <craigrouskey(a)gmail.com> wrote: > > What are the causes of burnout? > > > On Tue, Dec 17, 2013 at 2:08 PM, Romy Ilano <romy(a)snowyla.com> wrote: > >> we all go through cycles of hackerspace burn out. >> >> would it be nice to have a 2 minute therapy session on dealing with it? >> my hackerspace burn out cycles follow my life. It's easy to be cynical and >> burned out if you overdo things, or if you don't communicate - i think i'm >> back on the up and up though! >> >> >> ============================= >> >> Romy Ilano >> romy(a)snowyla.com >> >> >> >> _______________________________________________ >> sudo-discuss mailing list >> sudo-discuss(a)lists.sudoroom.org >> http://lists.sudoroom.org/listinfo/sudo-discuss >> >> > > _______________________________________________ > sudo-discuss mailing list > sudo-discuss(a)lists.sudoroom.org > http://lists.sudoroom.org/listinfo/sudo-discuss > >

12 years, 3 months

New sudoroom t shirt test (color from on demand start up zazzle)

by Romy Snowyla

Hi I got the new test sudoroom zazzle shirt. It was about $24 Advantages Looks nice People can choose the exact color fit and style - huge problem for small people like me since most shirts are too big Fast! I got this up and printed in a week with minimal time and effort I didn't have to put any up front costs and I'm broke so that's nice We don't have to deal with shipping or inventory Disadvantages Very small profit for sudoroom : we'd make $2-3 a shirt Tied to a commercial service T shirts are all new and cost $20-30 So we can't use used clothes stencils or mass producs on cheap $2 a pop hanes shirts It's not silkscreen Sent from my iPhone

12 years, 3 months

the bike situation @ sudo

by Chris Bee

Hey sudologists- It seems that we have become a locus of sorts for bikes in various states of disrepair, and they're starting to pile up in sudo. Until we (or I) can get on top of the situation, can we keep the bike population where it's at by holding off on donations/projects for the time being? Or, can we come up with a better storage solution for the less likely candidates for immediate rehabilitation? We're currently at seven bikes in sudo proper, which is awesome on one hand but slightly overwhelming on the other. (side note to Jenny- this does not apply to you, I agreed to help you with your fuzzy blue Grover bike and that's still on...I'm currently waiting on the tools to get 'er done. Inshallah.) -chrisbee

12 years, 3 months

datashield power strip is shite

by Jake

I plugged my laptop into this weird power strip thingy, a Datashield Model 85, that is from the Beige era of computing. i noticed a while later that it was not powered - so i hit the reset button on the power strip, and it clicked and came back on. after the third time i figured it was no good, and needed to be repaired and not used until then, so i was going to unplug it. But i saw something else was plugged into it, from far away via an extension cord. The new color laser printer! Oh Noes!! the poor printer was getting turned on and off repeatedly due to this bullshit powerstrip thing. So if the laser printer is upset now, it may be because of repeated on and off, which they don't like. I recommend it be plugged into a reliable power socket, so it can be on or off, and if left on it can go to sleep without being suddenly off and on again all the time. -jake

12 years, 3 months

A College Kid Couldn't Afford a 3D Printer, So He Built One Himself

by Eden In Oakland

http://mashable.com/2013/12/20/deltaprintr-3d-printer/?utm_cid=mash-com-g+-… A College Kid Couldn't Afford a 3D Printer, So He Built One Himself Deltaprintr Makes 3D Printing Affordable Show As List By Samantha Murphy Kelly1 day ago When college student Shai Schechter didn't have access to an affordable 3D printer on his SUNY Purchase campus in New York, he set out to build his own model — one that would still crank out 3D-printed objects, but at a much lower cost. "We have a laser- and powder-based 3D printer at school, but it costs about $500 for a bucket of powder and that only lasts for about one or two prints," Schechter said. "It's never used because it is so expensive and classes weren’t offered that much in the curriculum." He approached his sculpture professor about building a new 3D printer that uses plastic instead, and sought the help of three good friends. Schecter and his business partners launched a Kickstarter campaign to bring their low-cost design to the masses; the project nearly sold out of preorders in the first week alone. While a new MakerBot 3D printer costs $2,000, the Deltraprintr is significantly less: $475 unassembled or $685 assembled. It's available in two sizes, either 2 feet high (large) or 2.5 feet (extra large). "We are targeting educational institutions first, so people can learn how to assemble them," Schecter said. "When you buy a MakerBot, and you read a manual about how to use it, you don't learn a lot about how the printer and technology works. This is why we are offering the assembly manual on Kickstarter, too — we want people to really get their hands on it." The Deltaprintr uses three stepper motors, located under the acrylic platform where the objects are printed. Motors control the carriages that move the hot end and ultimately create the 3D-printed objects. Since a Deltaprintr design doesn't rqeuire as many parts as other 3D printers, the savings are passed on to consumers. "MakerBot uses belts to move the print head, but ours uses a fishing line," Schechter said. "With the fishing line, you can expand it to make it taller if you want by changing the aluminum rods. It allows it to go faster than the MakerBot and is more accurate. It allows it to go faster than the MakerBot and is more accurate." Although the Deltaprintr team is focusing on getting the product off the ground as an educational tool, it's eying the mass market, too. "We want it to have a place in education, but it's still for the everyday user," Schechter said. "We have a lot of ideas that we plan to execute in the next year to make the Deltaprintr even better and lower the cost even more." Image: Mashable, Christina Ascani Have something to add to this story? Share it in the comments. BONUS: I 3D Printed a Gun Topics: 3D, 3d printer, 3D printing, Apps and Software, Gadgets, kickstarter, Tech

12 years, 3 months

A College Kid Couldn't Afford a 3D Printer, So He Built One Himself

by Eden In Oakland

12 years, 3 months

Peer Production Project

by Eddan Katz

Hi Sudo folk. Happy Holidays. Hope everyone's getting some quality time with friends and family. and Happy New Year to those of you already heading off somewhere for vacation. 2141 Broadway Looking ahead to 2014, this email is about buying and rental possibilities for the current building 2135-2143 Broadway with actual numbers. If you'd like to get in touch with the landlords directly, you can email Laurie Cooperman Rosen at lscoop(a)comcast.net; or call George Rosen at 510-504-4259. I wanted to update everyone on a meeting Matt & I had with the landlord earlier this month about the possibilities regarding renting/selling/co-op equity of the building where Sudo Room and the Bay Area Public School are currently located. Matt - please correct any of the information that I may have missed or gotten wrong in the inset text below. Since the Bay Area Public School and Sudo Room may (or may not) imminently be moving to the Omni or other location, a new list has been created to further discussion and coalition-building that will continue to take place in the current space at http://lists.sudoroom.org/listinfo/hall. This proposal, to be very clear, does not and will not interfere with any of those plans to move nor with plans to stay at the current location decided by the collective of collectives. Below are the notes regarding how much the southern section of the 2143-2145 Broadway have been rented for in the past, how much they're willing to rent each room individually, the whole floor as a whole, and a graduated occupancy/rate proposal that gives time to attract other potential collaborators visiting the space, and getting a reduced price for the rental of that whole section of $6,500/month for 3 months. Otherwise, according to the proposal discussed, rental of the floor will go up to the market rental price of $8,500 at the end of that 3 months. The other option that has been discussed is putting together a co-op sale where groups and individuals can buy equity in that section of the building, either as a real estate transaction, or as crowd-funding equity shares. Group and individual ownership will participate in any profits and in the governance of the building. Peer Production / Sudo Hall The resulting community will be provisionally called Peer Production. In order to honor the pivotal role that Sudo Room and the other people that first moved into this building have accomplished for the community, the proposed discussion list will be called Sudo Hall. It will also be a priority of the Peer Production project to reach out to the innovative and inspiring stories of the other tenants that are already in the building - including Sound Room, Uptown Kitchen, Yummmeee, and the Pan Theater, among others. In terms of values, integrating with the community we're in and remaining inclusive to attract a broad spectrum of types of people will take priority over political posturing and ideological orthodoxy. The community invitation to join is intended to be welcoming to for-profit, non-profit, small partnership, crowd-fund equity start-up, cooperative corporation, and any other structure under which people best think they can get done what they want to achieve. The objective of Peer Production {Sudo Hall} still aspires to the core of Sudo Room's early description: Doing stuff together to make our community more openly accessible. Peer Production, I believe, is the common thread of the innovative and socially conscious projects that have emerged. If you'd like to talk about this further or just find out what's going on - you can join the Sudo Hall mailing list at http://lists.sudoroom.org/listinfo/hall. We'll take it offline from the sudo-discuss list, but I just wanted to let folks know that this discussion just got started. First order of business is getting more photos and more data about the place. Sudo Room has started a good page at https://sudoroom.org/wiki/2141_Broadway and hopefully there can be more valuable and useful information that will be available through Peer Production and Sudo Hall. > 2135-2143 Broadway > Dec. 6, 2013. 5pm. > > George Rosen. > Matt Senate. > Eddan Katz. > > ---- > Sudo-Hall > > University used to pay $14,000 for the whole floor. > EBMC paid $6,500. 8% annual increase. > > Sudo Room. $1500 > Robert. $1,000 > Dance Studio. $1,100 > Public School. $950. > Room next to it. $950. > Yellow Room $2,500. > Corner Room. $2,200. (access to roof). > > total now at $8,500. > willing to do $6,500. > > > ---- > extra notes > building $5.3 million. > 1.2 million fees. > > Buy - income stream. $4 million for whole building. > > losing $65,000 per year by them being empty. > > $1 million selling price for Sudo Hall wing. > > > Need to do pictures of rooms. & sq. ft. > send photos. > Non-profit rental. > > $6,500 x 3 mos. > whole floor - to start with - $13,000. >

12 years, 3 months

Jump to page:

2026

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

sudo-discuss