Hi, My name is Scott. I've been in the middle of upgrading a Seckit SK-GO² core-XY 3D printer. I'm about 90% done, but have lost interest in it. The machine has been an absolute workhorse with its large build volume, but I think it is time for Oppy (named after the rover) to move on to a new owner who can utilize and attend it properly. It needs about 3-5 hours of work to get it running, and maybe 3hrs of tuning. Worst case, it is loaded with aluminum extrusions, hardware, stepper motors, linear rails, and a Pi! Let me know if I can donate the printer to your space :) Regards, Scott Griffitts_______________________________________________

Welcome Scott! I’ve started taking a look at the printer. It’s a super nice machine! Way better than our other printers. I’m excited to help get it working! Mechanically it looks like it’s in good shape. It needs updated firmware. It has Marlin installed but the firmware is not configured for Core-XY and the three auto bed leveling z axis steppers (very nice!) are not hooked up to the control board. However there are cables for the steppers with it in the box of parts and the control board has drivers and plugs for the three other steppers. So basically we need someone who can install the correct firmware for this printer. The email below in the chain has info on the model of printer but this has an additional z axis mod (which is very nice!) which will require additional configuration. Options are marlin or klipper. I have never configured klipper but it seems nice. I’m doing the big push for burning man right now so I won’t be able to look at this more till September. If someone else has any experience with configuring 3D printer firmware it would be great for you to take this on! On Wed, Jul 26, 2023 at 12:58 PM Jake via sudo-discuss < sudo-discuss(a)sudoroom.org&gt; wrote: > We got a really nice 3D printer donation from someone I hope will > start coming > around and join us! Welcome Scott > > -jake > > ---------- Forwarded message ---------- > Date: Tue, 25 Jul 2023 21:39:31 -0700 > From: Scott Griffitts > Subject: Re: [sudo-info] 3D printer donation > > Hey, Dropped off the printer with Toby and met a few folks who were > excited, > skeptical, and questioning the printer. I figured I would share some > info on > it. > > Here is the page on the upgraded Z mod I did: > https://seckit3dp.design/kit/triple-z > > Here is the page for the main printer build: > https://github.com/SecKit/SK-Go_SK-Mini > > Here is some info on the firmware it can run: > https://www.klipper3d.org/ > (I think if you do some digging, you can find examples for the > kinematic bed) > > Here is the bed probe I used: > https://coex3d.com/products/bltouch-v3-1-automatic-bed-leveling-probe > > The stepper motor board used is big tree tech octopus v1.0 with > TMC2209 drivers > > If you have any other questions let me know :) > > Also, > If you guys need volunteers or anything, let me know. I’d love to help > out with really cool people like you guys. > > Regards > Scott Griffitts > > On Sat, 22 Jul 2023, Scott Griffitts wrote: > > > Hi, > > My name is Scott. I've been in the middle of > > upgrading a Seckit SK-GO² core-XY 3D printer. I'm > > about 90% done, but have lost interest in it. The > > machine has been an absolute workhorse with its > > large build volume, but I think it is time for Oppy > > (named after the rover) to move on to a new owner > > who can utilize and attend it properly. It needs > > about 3-5 hours of work to get it running, and maybe > > 3hrs of tuning. Worst case, it is loaded with > > aluminum extrusions, hardware, stepper motors, > > linear rails, and a Pi! > > Let me know if I can donate the printer to your > > space :) > > Regards, > > Scott Griffitts_______________________________________________ > sudo-discuss mailing list -- sudo-discuss(a)sudoroom.org > To unsubscribe send an email to sudo-discuss-leave(a)sudoroom.org > More options at > https://sudoroom.org/lists/postorius/lists/sudo-discuss.sudoroom.org/ > _______________________________________________

I have experience configuring Marlin, but I won't be able to get to this any sooner. Taylor, can I suggest that we tentatively plan to meet on Wednesday, September 16th? That will give you some recovery time after the Burn when we'll both be around, if you want the company. Scott, you mentioned an interest in volunteering. We'd love for you to volunteer! Are you available for a phone call, or to drop in to our meeting tonight (W. August 2nd)? It's in person and online: meet.waag.org/turtlesturtlesturtles *Andrew R Gross, (he/him)* 412.657.5332 - shrad.org <http://www.shrad.org> On Wed, Aug 2, 2023 at 2:31 AM Taylor Alexander via sudo-discuss < sudo-discuss(a)sudoroom.org&gt; wrote: > Here’s the controller it uses. There’s also a raspberry pi 4 mounted > under this, as well as a touch screen. > > > > On Tue, Aug 1, 2023 at 11:39 PM Taylor Alexander < > tlalexander(a)gmail.com&gt; wrote: > >> Welcome Scott! >> >> I’ve started taking a look at the printer. It’s a super nice machine! >> Way better than our other printers. I’m excited to help get it working! >> >> Mechanically it looks like it’s in good shape. It needs updated >> firmware. It has Marlin installed but the firmware is not configured for >> Core-XY and the three auto bed leveling z axis steppers (very nice!) are >> not hooked up to the control board. However there are cables for the >> steppers with it in the box of parts and the control board has drivers and >> plugs for the three other steppers. >> >> So basically we need someone who can install the correct firmware for >> this printer. The email below in the chain has info on the model of printer >> but this has an additional z axis mod (which is very nice!) which will >> require additional configuration. Options are marlin or klipper. I have >> never configured klipper but it seems nice. >> >> I’m doing the big push for burning man right now so I won’t be able >> to look at this more till September. If someone else has any experience >> with configuring 3D printer firmware it would be great for you to take this >> on! >> >> >> >> On Wed, Jul 26, 2023 at 12:58 PM Jake via sudo-discuss < >> sudo-discuss(a)sudoroom.org&gt; wrote: >> >>> We got a really nice 3D printer donation from someone I hope will >>> start coming >>> around and join us! Welcome Scott >>> >>> -jake >>> >>> ---------- Forwarded message ---------- >>> Date: Tue, 25 Jul 2023 21:39:31 -0700 >>> From: Scott Griffitts >>> Subject: Re: [sudo-info] 3D printer donation >>> >>> Hey, Dropped off the printer with Toby and met a few folks who were >>> excited, >>> skeptical, and questioning the printer. I figured I would share some >>> info on >>> it. >>> >>> Here is the page on the upgraded Z mod I did: >>> https://seckit3dp.design/kit/triple-z >>> >>> Here is the page for the main printer build: >>> https://github.com/SecKit/SK-Go_SK-Mini >>> >>> Here is some info on the firmware it can run: >>> https://www.klipper3d.org/ >>> (I think if you do some digging, you can find examples for the >>> kinematic bed) >>> >>> Here is the bed probe I used: >>> https://coex3d.com/products/bltouch-v3-1-automatic-bed-leveling-probe >>> >>> The stepper motor board used is big tree tech octopus v1.0 with >>> TMC2209 drivers >>> >>> If you have any other questions let me know :) >>> >>> Also, >>> If you guys need volunteers or anything, let me know. I’d love to >>> help out with really cool people like you guys. >>> >>> Regards >>> Scott Griffitts >>> >>> On Sat, 22 Jul 2023, Scott Griffitts wrote: >>> >>> > Hi, >>> > My name is Scott. I've been in the middle of >>> > upgrading a Seckit SK-GO² core-XY 3D printer. I'm >>> > about 90% done, but have lost interest in it. The >>> > machine has been an absolute workhorse with its >>> > large build volume, but I think it is time for Oppy >>> > (named after the rover) to move on to a new owner >>> > who can utilize and attend it properly. It needs >>> > about 3-5 hours of work to get it running, and maybe >>> > 3hrs of tuning. Worst case, it is loaded with >>> > aluminum extrusions, hardware, stepper motors, >>> > linear rails, and a Pi! >>> > Let me know if I can donate the printer to your >>> > space :) >>> > Regards, >>> > Scott Griffitts_______________________________________________ >>> sudo-discuss mailing list -- sudo-discuss(a)sudoroom.org >>> To unsubscribe send an email to sudo-discuss-leave(a)sudoroom.org >>> More options at >>> https://sudoroom.org/lists/postorius/lists/sudo-discuss.sudoroom.org/ >>> >> _______________________________________________ > sudo-discuss mailing list -- sudo-discuss(a)sudoroom.org > To unsubscribe send an email to sudo-discuss-leave(a)sudoroom.org > More options at > https://sudoroom.org/lists/postorius/lists/sudo-discuss.sudoroom.org/ > _______________________________________________ sudo-discuss mailing list -- sudo-discuss(a)sudoroom.org To unsubscribe send an email to sudo-discuss-leave(a)sudoroom.org More options at https://sudoroom.org/lists/postorius/lists/sudo-discuss.sudoroom.org/